Nissan Maxima. Instruction — part 790
INT-30
< REMOVAL AND INSTALLATION >
FLOOR TRIM
FLOOR TRIM
Exploded View
INFOID:0000000009465890
Removal and Installation
INFOID:0000000009465891
REMOVAL
1. Disconnect the negative and positive battery terminals. Refer to
PG-68, "Removal and Installation (Bat-
.
2. Remove front seat (RH/LH). Refer to
SE-68, "Removal and Installation"
(w/o climate controlled seats) or
SE-126, "Removal and Installation"
(with climate controlled seats).
3. Remove the rear seat cushion. Refer to
SE-70, "Removal and Installation"
(with fixed seatback, W/O CLI-
MATE CONTROLLED SEATS), or
SE-73, "Removal and Installation"
(with split seatback, W/O CLIMATE
SE-128, "Removal and Installation"
CLIMATE CONTROLLED SEATS)
SE-131, "Removal and Installation"
(with split seatback, WITH CLI-
MATE CONTROLLED SEATS).
4. Remove dash side lower finishers (RH/LH), front inner kick plates (RH/LH), rear inner kick plates (RH/LH)
and the center pillar lower garnishes (RH/LH). Refer to
INT-24, "Removal and Installation"
1.
Spacer (RH)
2.
Spacer (LH)
3.
Floor mat hook
4.
Floor carpet
5.
Harness clamp
Front
ALJIA0362ZZ
FLOOR TRIM
INT-31
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
5. Remove center console assembly. Refer to
IP-14, "Removal and Installation"
.
6. Remove the instrument stay bracket nuts (A), and the instru-
ment stay bracket (1).
7. Remove the connector duct (RH/LH) (2) and the center connec-
tor duct (1) from heater and cooling unit. Refer to
TER VENTILATOR GRILLES : Removal and Installation"
•
: Front
8. Disconnect the drain hose (4) from the heater and cooling unit
and set drain hose aside.
9. Remove the bracket bolts (A) and nut and the bracket (3).
10. Detach the center console harness clips (A), then disconnect the
center console harness electrical connectors (B) and position
the center console harness (1) aside.
11. Remove the parking brake cable nuts (A) and bolt and remove
the parking brake cable. Position the parking brake cable aside.
12. Remove the yaw rate/side/decel G sensor. Refer to
BRC-108, "Removal and Installation"
13. Remove the drivers air bag module. Refer to
SR-12, "Removal and Installation"
.
14. Remove the passenger air bag module. Refer to
SR-17, "Removal and Installation"
.
15. Remove the diagnosis sensor unit. Refer to
SR-31, "Removal and Installation"
.
ALJIA0348ZZ
ALJIA0009ZZ
ALJIA0349ZZ
ALJIA0350ZZ
INT-32
< REMOVAL AND INSTALLATION >
FLOOR TRIM
16. Remove the parking brake cable nuts (A). Position the parking
brake cables (2) aside.
17. Remove the bracket nuts (B), and remove extension bracket (1)
and center console rear bracket (3).
•
Front
18. Remove the CVT shift selector. Refer to
TM-170, "Removal and Installation"
.
19. Remove the CVT shift selector bracket bolts (A), and remove
the CVT shift selector bracket (1).
20. Remove front seat belt floor anchor bolt (RH/LH). Refer to
SB-6, "Removal and Installation"
.
21. Release the tab and remove the floor mat hook.
22. Release the tabs and open harness clamps (six R/H and six L/H). Position harness and floor carpet cut-
out areas outside of harness clamps.
23. Fold corners toward center, then remove floor carpet.
INSTALLATION
Installation is in the reverse order of removal.
ALJIA0363ZZ
ALJIA0351ZZ
HEADLINING
INT-33
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
HEADLINING
Exploded View
INFOID:0000000009465892
Removal and Installation
INFOID:0000000009465893
CAUTION:
• Disconnect the negative and positive battery terminals and wait at least three minutes.
AWJIA1164ZZ
1.
Rear assist grip
2.
Front assist grip
3.
Front room/map lamp assembly (dual pan-
el-sunroof)
4.
Sun visor (RH)
5.
Sun visor (LH)
6.
Mirror harness cover
7.
Sun visor cover
8.
Front room/map lamp assembly
9.
Sun visor holder
10. Rear assist grip LH
11. Headlining assembly (single panel sunroof) 12. Headlining assembly (dual panel-sunroof)
A.
Dual lock fastener
B.
Sunroof clip
C.
Screw
D.
Metal clip
E.
Magnets
F.
Clip
Front
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст