Nissan Maxima. Instruction — part 1205
TPMS
WT-9
< SYSTEM DESCRIPTION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
A sensor-transmitter integrated with a valve is installed in each
wheel. It transmits a detected air pressure signal in the form of a
radio wave when the vehicle is moving. The radio signal is received
by the tire pressure receiver.
TIRE PRESSURE RECEIVER
The tire pressure receiver (1) is located on the RH side of the steer-
ing column, and is shown with the lower instrument panel LH
removed. The tire pressure receiver receives the air pressure signal
transmitted by the transmitter in each wheel.
COMBINATION METER
The combination meter receives tire pressure status from the BCM
using CAN communication. When a low tire pressure condition is
sensed by the BCM, the combination meter low tire pressure warn-
ing lamp is activated. A CHECK TIRE PRESSURE warning mes-
sage will also be displayed in the vehicle information display. Refer
to the Owner’s Instruction for additional information.
TIRE PRESSURE WARNING CHECK CONNECTOR
The tire pressure warning check connector can be grounded in order
to initiate self-diagnosis without a CONSULT. Refer to
. The tire pressure warning check
connector (1) is located behind the lower portion of the instrument
panel LH, above the hood release handle.
WEIA0137E
AWEIA0123ZZ
LEIA0055E
AWEIA0121ZZ
WT-10
< SYSTEM DESCRIPTION >
TPMS
System Components
INFOID:0000000010046333
AWEIA0150ZZ
1.
Tire pressure receiver M70
2.
BCM M16, M17, M18, M19
3.
Transmitters
4.
Tire pressure warning check connector
M62
5.
Combination meter M24
DIAGNOSIS SYSTEM (BCM)
WT-11
< SYSTEM DESCRIPTION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
DIAGNOSIS SYSTEM (BCM)
CONSULT Function (BCM - COMMON ITEM)
INFOID:0000000010060544
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions.
CONSULT Function (BCM - AIR PRESSURE MONITOR)
INFOID:0000000010060545
NOTE:
The Signal Tech II Tool (J-50190) can be used to perform the following functions. Refer to the Signal Tech II
User Guide for additional information.
Direct Diagnostic Mode
Description
Ecu Identification
The BCM part number is displayed.
Self Diagnostic Result
Displays the diagnosis results judged by BCM.
Data Monitor
The BCM input/output signals are displayed.
Active Test
The signals used to activate each device are forcibly supplied from BCM.
Work support
Changes the setting for each system function.
Configuration
• Enables to read and save the vehicle specification.
• Enables to write the vehicle specification when replacing BCM.
CAN Diag Support Mntr
Monitors the reception status of CAN communication viewed from BCM.
System
Sub System
Direct Diagnostic Mode
Ecu Id
en
tificati
on
Sel
f Di
agn
os
tic Re
su
lt
Dat
a
M
on
ito
r
Acti
ve
T
est
W
ork
su
pp
ort
Co
nf
ig
ur
at
io
n
CAN Diag S
upport Mntr
Door lock
DOOR LOCK
×
×
×
×
Rear window defogger
REAR DEFOGGER
×
×
Warning chime
BUZZER
×
×
Interior room lamp timer
INT LAMP
×
×
×
Exterior lamp
HEADLAMP
×
×
×
Wiper and washer
WIPER
×
×
×
Turn signal and hazard warning lamps FLASHER
×
×
×
Intelligent Key system
INTELLIGENT KEY
×
×
×
Combination switch
COMB SW
×
BCM
BCM
×
×
×
×
×
Immobilizer
IMMU
×
×
×
Interior room lamp battery saver
BATTERY SAVER
×
×
×
Trunk open
TRUNK
×
×
Vehicle security system
THEFT ALM
×
×
×
RAP system
RETAINED PWR
×
Signal buffer system
SIGNAL BUFFER
×
×
TPMS
AIR PRESSURE MONITOR
×
×
×
×
WT-12
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
• Activate and display TPMS transmitter IDs
• Display tire pressure reported by the TPMS transmitter
• Read TPMS DTCs
• Register TPMS transmitter IDs
SELF DIAGNOSTIC RESULT
NOTE:
Before performing Self Diagnostic Result, be sure to register the ID, or else the actual malfunction may be dif-
ferent from that displayed on CONSULT.
DATA MONITOR
ACTIVE TEST
WORK SUPPORT
Monitor Item
Condition
Specification
AIR PRESS FL
• Drive vehicle for a few minutes.
or
• Ignition switch ON and activation tool is trans-
mitting activation signals.
Tire pressure (kPa, kg/cm
2
or Psi)
AIR PRESS FR
AIR PRESS RR
AIR PRESS RL
ID REGST FL1
Ignition switch ON
Registration ID: Green
No registration: Red
ID REGST FR1
ID REGST RR1
ID REGST RL1
WARNING LAMP
Ignition switch ON
Low tire pressure warning lamp on: ON
Low tire pressure warning lamp off: OFF
BUZZER
Ignition switch ON
Buzzer in combination meter on: ON
Buzzer in combination meter off: OFF
Test Item
Description
WARNING LAMP
This test is able to check tire pressure warning lamp operation [On/Off].
ID REGIST WARNING
This test is able to check ID regist warning chime operation [On/Off].
FLASHER
This test is able to check turn signal lamp operation [Off/LH/RH].
HORN
This test is able to check horn operation [On].
Support Item
Description
ID READ
The registered ID number is displayed.
ID REGIST
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст