Nissan Maxima. Instruction — part 994
GLASS LID
RF-149
< REMOVAL AND INSTALLATION >
[WITH DUAL PANEL SUNROOF]
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
REMOVAL AND INSTALLATION
GLASS LID
Removal and Installation
INFOID:0000000009465744
REMOVAL
CAUTION:
• Always work with a helper.
• Handle glass lid with care to prevent damage.
NOTE:
For easier and more accurate installation, always mark each point before removal.
1. Open sunshade.
2. Tilt glass lid up, then slide rearward to expose all the glass lid bolts.
3. Release the slide clip, then remove inner blind (1) (LH/RH) from
the glass lid (2).
: Front
4. Remove the glass lid rear bolts (A), two on both the left and right
sides.
: Front
5. Remove the glass lid front bolts (B), two on both the left and
right sides.
: Front
6. Remove the glass lid from the vehicle.
INSTALLATION
CAUTION:
After installing the glass lid, perform the water leak test.
Installation is in the reverse order of removal.
NOTE:
• After installing, perform glass lid adjustment procedure. Refer to
RF-155, "Inspection and Adjustment"
.
ALKIA1654ZZ
ALKIA1652ZZ
ALKIA1653ZZ
RF-150
< REMOVAL AND INSTALLATION >
[WITH DUAL PANEL SUNROOF]
GLASS LID
• After adjustment, always check for proper sunroof operation. If necessary, perform initialization procedure to
synchronize entire system. Refer to
SUNROOF MOTOR ASSEMBLY
RF-151
< REMOVAL AND INSTALLATION >
[WITH DUAL PANEL SUNROOF]
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
SUNROOF MOTOR ASSEMBLY
Removal and Installation
INFOID:0000000009465745
REMOVAL
CAUTION:
• Before removing sunroof motor, check that glass lid is fully closed.
• After removing sunroof motor, do not attempt to rotate sunroof motor assembly as a single unit.
1. Close glass lid.
2. Remove the headlining. Refer to
INT-33, "Removal and Installation"
.
3. Disconnect the harness connector (A) from the sunroof motor
assembly.
4. Remove sunroof motor assembly screws (B), then remove sun-
roof motor assembly (1) from sunroof unit assembly frame.
INSTALLATION
CAUTION:
Before installing the sunroof motor assembly, be sure to the place the link and wire assembly in the
symmetrical and fully closed position.
1. Move the sunroof motor assembly laterally so that the gear is completely engaged into the wire on the
sunroof unit assembly frame, and mounting surface becomes parallel.
2. Install and tighten sunroof motor assembly screws.
3. Connect the harness connector to the sunroof motor assembly.
4. Install the headlining. Refer to
INT-33, "Removal and Installation"
5. Perform initilization procedure. Refer to
RF-76, "ADDITIONAL SERVICE WHEN REPLACING CONTROL
UNIT : Special Repair Requirement"
ALKIA1655ZZ
RF-152
< REMOVAL AND INSTALLATION >
[WITH DUAL PANEL SUNROOF]
SUNSHADE MOTOR ASSEMBLY
SUNSHADE MOTOR ASSEMBLY
Removal and Installation
INFOID:0000000009465746
REMOVAL
CAUTION:
• Before removing sunshade motor, check that glass lid is fully closed.
• After removing sunshade motor, do not attempt to rotate sunshade motor assembly as a single unit.
1. Close glass lid.
2. Remove the headlining. Refer to
INT-33, "Removal and Installation"
.
3. Disconnect the harness connector (A) from the sunshade motor
assembly.
4. Remove sunroof motor assembly screws (B), then remove sun-
roof motor assembly (1) from sunroof unit assembly frame.
INSTALLATION
CAUTION:
Before installing the sunshade motor assembly, be sure to the place the link and wire assembly in the
symmetrical and fully closed position.
1. Move the sunshade motor assembly laterally so that the gear is completely engaged into the wire on the
sunroof unit assembly frame, and mounting surface becomes parallel.
2. Install and tighten sunshade motor assembly screws.
3. Connect the harness connector to the sunshade motor assembly.
4. Install the headlining. Refer to
INT-33, "Removal and Installation"
5. Perform initilization procedure. Refer to
RF-76, "ADDITIONAL SERVICE WHEN REPLACING CONTROL
UNIT : Special Repair Requirement"
ALKIA1659ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст