Nissan Maxima. Instruction — part 1180

TM-184

< REMOVAL AND INSTALLATION >

[CVT: RE0F09B]

SECONDARY SPEED SENSOR

SECONDARY SPEED SENSOR

Exploded View

INFOID:0000000010114023

Removal and Installation

INFOID:0000000009469212

REMOVAL

1. Disconnect the battery negative terminal. Refer to

PG-67, "Removal and Installation (Battery)"

.

2. Remove hoodledge cover (LH).
3. Remove engine room cover.
4. Remove front air duct. Refer to

EM-24, "Removal and Installation"

.

5. Remove air cleaner case assembly. Refer to

EM-24, "Removal and Installation"

6. Disconnect secondary speed sensor harness connector.
7. Remove secondary speed sensor (1) and shim (2).

CAUTION:

Do not lose the shim.

8. Remove O-ring (3) from secondary speed sensor.

CAUTION:

Do not reuse O-ring.

INSTALLATION

Installation is in the reverse order of removal.

CAUTION:

• Do not reuse O-ring.

• Apply CVT fluid to O-ring.

Inspection

INFOID:0000000010114024

Check for CVT fluid leakage and check CVT fluid level. Refer to

TM-155, "Inspection"

.

1.

Secondary speed sensor

2.

Shim

3.

Transaxle assembly

4.

O-ring

Apply CVT Fluid NS-2

JPDIA0687GB

JPDIA0617ZZ

DIFFERENTIAL SIDE OIL SEAL

TM-185

< REMOVAL AND INSTALLATION >

[CVT: RE0F09B]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

DIFFERENTIAL SIDE OIL SEAL

Exploded View

INFOID:0000000010114211

Removal and Installation

INFOID:0000000009469215

REMOVAL

1. Remove front fender protector side cover. Refer to

EXT-16, "Removal and Installation"

.

2. Remove front drive shafts. Refer to

FAX-9, "Removal and Installation (LH)"

(LH) and

FAX-10, "Removal

and Installation (RH)"

(RH).

3. Remove differential side oil seals (1) using a suitable tool (A).

CAUTION:

Be careful not to scratch transaxle case and converter

housing.

INSTALLATION

Installation is in the reverse order of removal.

• Install each differential side oil seal evenly using Tool so that differ-

ential side oil seal protrudes by the dimension (C) respectively.

CAUTION:

• Do not reuse differential side oil seals.

1.

RH differential side oil seal

2.

LH differential side oil seal

3.

Transaxle assembly

Apply CVT Fluid NS-2

JPDIA0593ZZ

JPDIA0118ZZ

(A)

: Transaxle case side

(B)

: Converter housing side

Dimension (C)

: 0

± 0.5 mm (0 ± 0.020 in)

Tool number

: ST33400001 (J-26082)

JPDIA0618ZZ

TM-186

< REMOVAL AND INSTALLATION >

[CVT: RE0F09B]

DIFFERENTIAL SIDE OIL SEAL

• Apply CVT fluid to differential side oil seals.

NOTE:

Differential side oil seal removal direction is used as the reference.

Inspection

INFOID:0000000010114212

Check for CVT fluid leakage and check CVT fluid level. Refer to

TM-155, "Inspection"

.

AIR BREATHER HOSE

TM-187

< REMOVAL AND INSTALLATION >

[CVT: RE0F09B]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

AIR BREATHER HOSE

Exploded View

INFOID:0000000010114213

Removal and Installation

INFOID:0000000009469218

REMOVAL

1. Remove front air duct. Refer to

EM-24, "Removal and Installation"

.

2. Remove air cleaner case assembly. Refer to

EM-24, "Removal and Installation"

.

3. Remove air breather hose from transaxle assembly.

INSTALLATION

Installation is in the reverse order of removal.

CAUTION:

• Install air breather hose with paint mark facing front.

• Insert air breather hose onto air breather tube until overlap area reaches the spool.

• Install air breather hose to heater pipe and air cleaner case assembly by fully inserting the clip.

• Make sure there are no pinched or restricted areas on air breather hose caused by bending or wind-

ing when installing it.

1.

Air cleaner case

2.

Air breather hose

3.

Transaxle assembly

4.

Heater pipe

5.

Clip

A.

Paint mark

Front

ALDIA0035ZZ