Nissan Maxima. Instruction — part 236
BR-12
< BASIC INSPECTION >
BRAKE TUBE AND HOSE
BRAKE TUBE AND HOSE
Hydraulic Circuit
INFOID:0000000009466582
CAUTION:
• All hoses and piping (tubes) must be free from excessive bending, twisting and pulling.
• Make sure there is no interference with other parts when turning the steering wheel both clockwise
and counterclockwise.
• The brake piping is an important safety part. If a brake fluid leak is detected, always disassemble the
parts. Replace applicable part with a new one, if necessary.
• Be careful not to splash brake fluid on painted areas; it may cause paint damage. If brake fluid is
splashed on painted areas, wash it away with water immediately.
• Do not bend or twist brake hose sharply, or strongly pull it.
• When removing components, cover connections so that no dirt, dust, or other foreign matter gets in.
• Refill with new specified brake fluid. Refer to
MA-15, "FOR USA AND CANADA : Fluids and Lubri-
(for United States and Canada) or
MA-16, "FOR MEXICO : Fluids and Lubricants"
• Do not reuse drained brake fluid.
FRONT BRAKE
FRONT BRAKE : Inspection
INFOID:0000000009466583
INSPECTION AFTER REMOVAL
CAUTION:
Brake tubes and hoses are important safety parts. Always disassemble the parts and retighten their fit-
tings, if a brake fluid leak is detected. Replace applicable part with a new one, if damaged part is
detected.
1.
Actuator
2.
Master cylinder
3.
Brake booster
4.
Connector
A.
Union bolt
18.2 N·m (1.9 kg-m, 13 ft-lb)
B.
Flare nut M12
22.1 N·m (2.3 kg-m, 16 ft-lb)
C.
Flare nut M10
16.2 N·m (1.7 kg-m, 12 ft-lb)
AWFIA0432ZZ
BRAKE TUBE AND HOSE
BR-13
< BASIC INSPECTION >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
1. Check brake lines (tubes and hoses) and connections for fluid leaks, damage, twists, deformation, con-
tacts with other parts, and loose connections. Replace any parts as necessary. Refer to
and Installation of Front Brake Piping and Brake Hose"
2. While depressing brake pedal under a force of 785 N (80 kg, 177 lb) with engine running for approximately
5 seconds, check each part for fluid leaks.
REAR BRAKE
REAR BRAKE : Inspection
INFOID:0000000009466584
INSPECTION AFTER REMOVAL
CAUTION:
Brake tubes and hoses are important safety parts. Always disassemble the parts and retighten their fit-
tings, if a brake fluid leak is detected. Replace applicable part with a new one, if damaged part is
detected.
1. Check brake lines (tubes and hoses) and connections for fluid leaks, damage, twists, deformation, con-
tacts with other parts, and loose connections. Replace any parts as necessary. Refer to
and Installation of Rear Brake Piping and Brake Hose"
.
2. While depressing brake pedal under a force of 785 N (80 kg, 177 lb) with engine running for approximately
5 seconds, check each part for fluid leaks.
BR-14
< PERIODIC MAINTENANCE >
BRAKE PEDAL
PERIODIC MAINTENANCE
BRAKE PEDAL
Inspection and Adjustment
INFOID:0000000009466585
INSPECTION
1. Inspect the brake pedal free height (H) from the floor using Tool
at a 90
° angle to the floor as shown.
2. Adjust the brake pedal free height (H) to specifications.
ADJUSTMENT
1. Loosen the stop lamp switch and ASCD cancel switch by turning 45
° counterclockwise.
Tool number :
—
(J-46532)
AWFIA0557ZZ
Brake pedal free height (H)
.
Brake pedal full stroke (S)
.
Clearance between brake pedal bracket (C
1
) and threaded end of stop lamp switch
and ASCD cancel switch (C
2
)
.
BRAKE PEDAL
BR-15
< PERIODIC MAINTENANCE >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
2. Loosen lock nut (A) on the input rod, then turn input rod to adjust
the brake pedal to specified height. When finished adjusting,
tighten lock nut (A) to specification.
CAUTION:
Make sure that the screw portion of the end of input rod is
located inside the clevis.
3. With the brake pedal pulled up and held by hand, press the stop
lamp switch and the ASCD cancel switch in until threaded ends
contact the brake pedal bracket.
4. With the threaded ends of the stop lamp switch and ASCD can-
cel switch contacting the pedal bracket, turn the switches 45
°
clockwise to lock in place. Check that the stop lamp switch and
ASCD cancel switch threaded end to brake pedal bracket gap
(C) is within specifications.
CAUTION:
Make sure that the gap (C) between the brake pedal bracket
and stop lamp switch and ASCD cancel switch threaded
ends are within specification.
5. Check the brake pedal for smooth operation.
CAUTION:
Make sure that the stop lamp goes off when the brake pedal
is released.
Lock nut (A)
: 18.7 N·m (1.9 kg-m, 14 ft-lb)
PFIA0436E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст