Nissan Maxima. Instruction — part 1119
TELESCOPIC MOTOR
ST-21
< REMOVAL AND INSTALLATION >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
The tilt/telescope switch can remain attached to the side cover.
5. Remove telescope motor as follows.
1. Disconnect the harness connector (A) from the telescope
motor.
2. Remove the two telescope motor link screws (B) and tele-
scope motor link bracket.
3. Remove telescope motor bolt (C).
4. Remove the telescope motor (D).
NOTE:
If the steering wheel could not be telescoped to full out posi-
tion instructionly pull steering wheel to the full out position.
INSTALLATION
Installation is in the reverse order of removal.
NOTE:
• Adjust the telescope motor link to full out position and adjust as needed to fit into proper installed position.
• Inform customer that they will need to reset their Automatic Drive Positioner (ADP) settings.
ALGIA0053ZZ
ST-22
< REMOVAL AND INSTALLATION >
STEERING COLUMN
STEERING COLUMN
Exploded View
INFOID:0000000009465778
Without Electric Motor
AWGIA0105GB
1-4.
Steering column assembly nut tight-
ening order
5.
Steering wheel
6.
Combination switch and spiral cable
7.
Steering column assembly
8.
Hole cover seal
9.
Herbie clip
10.
Hole cover
11. Lower shaft assembly
STEERING COLUMN
ST-23
< REMOVAL AND INSTALLATION >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
With Electric Motor
Removal and Installation
INFOID:0000000009465779
REMOVAL
Hole Cover Seal, Hole Cover and Lower Shaft Assembly
1. Set wheels to the straight-ahead position.
2. Remove lower side bolt (A) of lower shaft assembly (1).
• Steering gear (2)
3. Remove the instrument lower panel LH. Refer to
IP-19, "Removal and Installation"
.
AWGIA0098GB
1-4.
Steering column assembly nut tight-
ening order
5.
Steering wheel
6.
Combination switch and spiral cable
7.
Steering column assembly
8.
Hole cover seal
9.
Herbie clip
10.
Hole cover
11. Lower shaft assembly
ALGIA0041ZZ
ST-24
< REMOVAL AND INSTALLATION >
STEERING COLUMN
4. Remove bolt (A) and nut (B) of column upper joint (2), then
remove lower shaft assembly (1).
CAUTION:
Do not reuse column upper joint nut.
5. Loosen herbie clip, then remove hole cover seal from hole
cover.
6. Remove nuts of hole cover, and then remove clamp and hole
cover from dash panel.
Steering Column Assembly
1. Set wheels to the straight-ahead position.
2. Remove instrument side finisher (LH). Refer to
.
3. Remove instrument lower panel LH. Refer to
IP-19, "Removal and Installation"
.
4. Remove lower knee protector (LH) bolts (
)(, then remove
lower knee protector (LH) (1). Refer to
5. Remove steering column upper and lower covers. Refer to
6. Remove combination switch and spiral cable. Refer to
7. Disconnect each switch harness connector installed to steering
column assembly, and then disconnect harness clips from steer-
ing column assembly.
8. Remove bolt (A) and nut (B) of column upper joint (2).
• Lower shaft assembly (1)
CAUTION:
Do not reuse column upper joint nut.
9. Remove steering column assembly nuts, then remove steering
column assembly.
INSPECTION AFTER REMOVAL
Hole Cover Seal, Hole Cover and Lower Shaft Assembly
Check each part of hole cover seal, hole cover and steering column and lower shaft assembly for damage or
other malfunctions. Replace if necessary.
Steering Column Assembly
• Check each part of steering column assembly for damage or other malfunctions. Replace entire steering col-
umn assembly if any parts are damaged.
• Measure the length (L) as shown if vehicle has been involved in a
minor collision. Replace steering column assembly if outside the
specifications.
ALGIA0042ZZ
ALGIA0043ZZ
ALGIA0042ZZ
Steering column length (L)
: Refer to
SGIA1177E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст