Nissan Maxima. Instruction — part 781
PREPARATION
INL-83
< PREPARATION >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000009465447
The actual shapes of the tools may differ from those illustrated here.
Tool number
(TechMate No.)
Tool name
Description
—
(J-46534)
Trim Tool Set
Removing trim components
AWJIA0483ZZ
INL-84
< REMOVAL AND INSTALLATION >
INTERIOR ROOM LAMP
REMOVAL AND INSTALLATION
INTERIOR ROOM LAMP
Removal and Installation
INFOID:0000000009465448
FRONT ROOM/MAP LAMP ASSEMBLY
Removal
1. Release the metal clips and drop front edge of front room/map
lamp assembly (1) away from headlining. Slide front room/map
lamp assembly forward in vehicle to clear pawls at rear.
: Front
: Pawl
: Metal clip
2. Disconnect the connectors, then remove the front room/map
lamp assembly.
Installation
Installation is in the reverse order of removal.
Bulb or Lens Replacement
WARNING:
Do not touch bulb while it is lit or right after being turned OFF. Burning may result.Caution: -Do not
touch glass surface of the bulb with bare hands or allow oil or grease to get on it to prevent damage to
bulb.
1. Using a suitable tool (A), remove the front room/map lamp lens
(2).
2. Pull bulb (1) straight out to remove.
3. Install the new bulb to front room/map lamp.
4. Install the front room/map lamp lens (2).
VANITY MIRROR LAMP
Removal
The vanity mirror lamp is replaced as part of the sun visor assembly. Refer to
INT-33, "Removal and Installa-
.
Installation
Installation is in the reverse order of removal.
Bulb or Lens Replacement
WARNING:
Do not touch bulb while it is lit or right after being turned OFF. Burning may result.Caution: -Do not
attempt to separate the vanity mirror lamp from the sun visor or damage to the components may
occur. -Do not touch glass surface of the bulb with bare hands or allow oil or grease to get on it to pre-
vent damage to bulb.
AWLIA1659ZZ
AWLIA2201ZZ
INTERIOR ROOM LAMP
INL-85
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
1. Using a suitable tool (A), remove the vanity mirror lamp lens (2).
2. Pull bulb (1) straight out to remove.
3. Install the new bulb to vanity mirror lamp.
4. Install the vanity mirror lamp lens (2).
GLOVE BOX LAMP
Removal
1. Remove the glove box assembly (1). Refer to
2. Rotate glove box lamp socket (3) and bulb (2) counterclockwise
and then pull out to remove.
Installation
Installation is in the reverse order of removal.
Bulb Replacement
WARNING:
Do not touch bulb while it is lit or right after being turned OFF. Burning may result.Caution: -Do not
touch glass surface of the bulb with bare hands or allow oil or grease to get on it to prevent damage to
bulb.
1. Remove the glove box lamp. Refer to GLOVE BOX LAMP.
2. Pull bulb straight out to remove.
3. Install the new bulb to glove box lamp.
4. Install the glove box lamp lens (2).
STEP LAMP
Removal
AWLIA2202ZZ
ALLIA0012ZZ
ALLIA0013ZZ
INL-86
< REMOVAL AND INSTALLATION >
INTERIOR ROOM LAMP
1. Insert a suitable tool between door finisher and step lamp lens/socket to release the pawls.
2. Disconnect the step lamp connector, then remove step lamp.
Installation
Installation is in the reverse order of removal.
Bulb Replacement
WARNING:
Do not touch bulb while it is lit or right after being turned OFF. Burning may result.Caution: -Do not
touch glass surface of the bulb with bare hands or allow oil or grease to get on it to prevent damage to
bulb.
1. Remove the step lamp lens/socket.
2. Pull the bulb straight out to remove.
3. Install the new bulb to step lamp.
4. Install the step lamp lens (2).
FOOT LAMP
Removal - LH
1. Using a suitable tool, release the foot lamp pawls and remove the foot lamp from the instrument lower
panel LH.
2. Disconnect the harness connector and remove the foot lamp.
Installation - LH
Installation is in the reverse order of removal.
Removal - RH
1. Rotate foot lamp socket counterclockwise to release from the substrate.
2. Disconnect the harness connector and remove the foot lamp.
Installation - RH
Installation is in the reverse order of removal.
Bulb Replacement
WARNING:
Do not touch bulb while it is lit or right after being turned OFF. Burning may result.Caution: -Do not
touch glass surface of the bulb with bare hands or allow oil or grease to get on it to prevent damage to
bulb.
1. Remove the foot lamp. Refer to FOOT LAMP.
2. Pull bulb straight out to remove.
3. Install the new bulb to foot lamp.
4. Install the foot lamp lens (2).
PERSONAL LAMP
Removal
The personal lamp is replaced as part of the headlining assembly. Refer to
INT-33, "Removal and Installation"
.
Installation
Installation is in the reverse order of removal.
Bulb or Lens Replacement
WARNING:
Do not touch bulb while it is lit or right after being turned OFF. Burning may result.Caution: -Do not
touch glass surface of the bulb with bare hands or allow oil or grease to get on it to prevent damage to
bulb.
1.
Step lamp connector
2.
Door finisher
3.
Step lamp lens/socket
4.
Step lamp bulb
Front
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст