Nissan Maxima. Instruction — part 1091
SIDE AIR BAG MODULE
SR-25
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
8. Disconnect the harness connector from the side air bag.
9. Remove and discard the two side air bag module nuts (1), then
remove the side air bag module.
CAUTION:
Do not reuse the side air bag module nuts.
ASSEMBLY
Assembly is in the reverse order of disassembly. During assembly, note the following.
• Make sure the chute rod is properly positioned and installed as shown.
: Front
ALJIA0653ZZ
Air bag module nuts (1)
: 8.2 N·m (0.84 kg-m, 73 in-lb)
ALJIA0595ZZ
ALJIA0654ZZ
SR-26
< REMOVAL AND INSTALLATION >
SIDE AIR BAG MODULE
• Make sure the side air bag outer chute (7) is pulled over the side
air bag module (3) and the side air bag inner chute (4) is pulled
around the frame (2). Make sure there are no wrinkles and the
chutes are not folded, twisted or pinched.
(1) Seatback pad
(2) Frame
(3) Side air bag module
(4) Inner side air bag chute
(5) Chute rod
(6) Seatback board
(7) Outer chute
: Front
CAUTION:
• If a malfunction was detected by the air bag warning lamp, after repair or replacement of the mal-
function parts, reset the memory using self-diagnosis or CONSULT.
• After work is completed, check that no system malfunction is detected by air bag warning lamp.
• Make sure side air bag module shell is closed at all tabs and cushion of module is not exposed. Do
not reuse if the tab of shell is not secured.
• Always install new side air bag module attaching nuts and side air bag chute rod bolts.
• Always route side air bag module harness in original location. Replace any deformed or damaged
clips with the same type and color. Always install clips in the original location on the harness.
• Smooth out all wrinkles during assembly.
• Inspect seatback cushion, trim cover and trim cover chutes. Replace any damaged parts.
• Replace any deformed or damaged parts.
ALJIA0655ZZ
CRASH ZONE SENSOR
SR-27
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
CRASH ZONE SENSOR
Component
INFOID:0000000009471848
Removal and Installation
INFOID:0000000009471849
CAUTION:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes.
• Do not use air tools or electric tools for servicing.
• Replace the crash zone sensor of deployed SRS driver air bag and deployed SRS front passenger air
bag.
• Do not cause impact to the crash zone sensor by dropping
etc. Replace the crash zone sensor if it has been dropped or
sustained an impact.
REMOVAL
1. Disconnect the negative and positive battery terminals, then wait at least 3 minutes. Refer to
"Removal and Installation (Battery)"
.
2. Remove the front air duct, then position upper radiator hose aside.
1.
Crash zone sensor harness connector
2.
Crash zone sensor
A.
Nut
Front
ALHIA0131GB
JMHIA0009ZZ
SR-28
< REMOVAL AND INSTALLATION >
CRASH ZONE SENSOR
3. Disconnect the harness connector the crash zone sensor.
4. Remove the nuts, then remove crash zone sensor.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not use old crash zone sensor nuts after removal; replace with new nuts.
• Be careful not to damage the crash zone sensor harness.
• After the work is completed, make sure no system malfunction is detected by air bag warning lamp.
• In case a malfunction is detected by the air bag warning lamp, reset by the self-diagnosis function
and delete the memory by CONSULT.
• If a malfunction is still detected after the above operation, perform self-diagnosis to repair malfunc-
tions. Refer to
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст