Nissan Juke F15. Instruction — part 1114
FRONT SEAT
SE-21
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
*: passenger seat only
Removal and Installation
INFOID:0000000012196880
REMOVAL
CAUTION:
Before servicing, disconnect the battery cable from negative terminal or remove the fuse.
1. Remove headrest.
2. Set the seatback vertically.
3. Slide seat to the frontmost position.
4. Remove rear outer mounting TORX bolt.
5. Remove rear inner mounting TORX bolt.
6. Slide seat to the rearmost position.
7. Remove front outer mounting TORX bolt.
8. Remove front inner mounting TORX bolt.
9. Remove seat cushion lower harness connectors and harness fixing clamps.
CAUTION:
Before performing removal operation, check the installation position of harness connectors and
harness fixing clamps.
10. Remove seat from the vehicle.
CAUTION:
When removing and installing, use shop cloths to protect parts from damage.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• When removing and installing, use shop cloths to protect parts from damage.
• When installing, tighten mounting TORX bolts according to
the numerical order (1, 2, 3, and 4 as shown in the figure),
starting from front inner mounting TORX bolt.
• Always fix the harness fixing clamp in position.
SEATBACK
SEATBACK : Disassembly and Assembly
INFOID:0000000012196881
DISASSEMBLY
Without RECARO seat model
CAUTION:
10. Lifter lever cap
11. Occupant sensor harness
*
12. Reclining knob
13. Frame carpet
: Pawl
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
JMJIA4591ZZ
SE-22
< REMOVAL AND INSTALLATION >
FRONT SEAT
For models with heater seat, always replace heater seat as a seatback assembly without disassem-
bling trim and pad.
1. Remove seatback retainer installed in the lower portion of seat cushion.
2. Remove harness installed in the lower portion of seat cushion.
1. Disconnect seatback heater unit harness connector
(A).(with heater seat only.)
2. Remove seatback heater unit harness connector fixing clips
and harness fixing clamp (B). (with heater seat only)
3. Disconnect side air bag module harness connector (C).
4. Remove side air bag module harness connector fixing clips
and harness fixing clamp (D).
3. Open seatback fastener (A) and remove seatback retainer (B).
4. Remove side air bag module harness fixing clamps from seat frame & adjuster assembly.
5. Use pincers, etc., to press up pawls as shown by the arrows in
the figure, and remove headrest holder from seatback.
CAUTION:
Before installing headrest holder check its orientation.
(front/rear and right/left)
6. Remove side air bag module mounting nuts.
7. Remove seatback trim and seatback pad from seat frame & adjuster assembly.
CAUTION:
Never subject side air bag module to impact by dropping or hitting.
8. Remove side air bag module from seatback pad.
9. Separate the seatback trim and seatback pad. (without heater seat only)
Remove hog rings, and separate the seatback trim and seatback pad.
CAUTION:
Before performing separating operation, check the installation position of hog rings.
10. Remove seatback silencer from seat frame & adjuster assembly.
With RECARO seat model
: Vehicle front
JMJIA4602ZZ
JMJIA4363ZZ
PIIB4084J
FRONT SEAT
SE-23
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
1. Cut harness clip (A) and disengage side air bag harness connector (B), harness clip (C).
2. Remove lifter lever.
a. Disengage lifter lever cap fixing pawls, and then remove lifter
lever cap.
b. Remove lifter lever fixing screws (A), and then remove lifter
lever.
3. Remove seat cushion finisher fixing screws (A), and then
remove seat cushion finisher.
Passenger side
Driver side
: Clip
JMJIB0213ZZ
: Pawl
JMJIB0110ZZ
JMJIB0111ZZ
JMJIB0112ZZ
SE-24
< REMOVAL AND INSTALLATION >
FRONT SEAT
4. Remove reclining device cover fixing screw (A), and then
remove reclining device cover while disengage reclining device
cover fixing pawls.
5. Remove seatback assembly fixing screws (A), and then remove
seatback assembly.
NOTE:
• Disengage reclining knob fixing pawl, and then remove reclining
knob.
ASSEMBLY
Note the following items, and then assemble in the reverse order of disassembly.
Without RECARO seat model
CAUTION:
• For hog ring that is removed or crimped unsuccessfully, fix it by using a new hog ring. (Never reuse
hog ring.)
• Always install the hog rings in position.
With RECARO seat model
CAUTION:
• When installing seatback assembly, temporary tighten all
seatback assembly fixing bolts, and then tighten fixing bolts
according to the numerical order 1
→4 indicated by as shown
in the figure, starting from front right fixing bolt.
: Pawl
JMJIB0113ZZ
JMJIB0114ZZ
: Pawl
JMJIB0115ZZ
JMJIB0116ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст