Nissan Juke F15. Instruction — part 32
AV-114
< BASIC INSPECTION >
[AUDIO WITH NAVIGATION]
INSPECTION AND ADJUSTMENT
>> GO TO 5.
5.
WRITE VEHICLE SPECIFICATION
CONSULT Configuration
Select “Instruction Configuration”, and write the setting value as shown in the following table to NAVI control unit
according to the vehicle specification.
CAUTION:
Grasp vehicle specifications precisely. The control of ECU may not function normally if the specifica-
tions are misread.
NOTE:
• The items shown in this list depend on vehicle specifications.
• The config list may not be displayed depending on vehicle specifications. This is not a malfunction.
• If selection items are not displayed on the CONSULT screen, touch “NEXT”.
>> GO TO 6.
6.
PERFORM SELF-DIAGNOSIS
CONSULT Self Diagnostic Result
Perform self-diagnosis of CONSULT, and check whether or not DTC U12AA is detected.
Is DTC U12AA detected?
YES
>> GO TO 5.
NO
>> GO TO 7.
7.
OPERATION CHECK
Check that the operation of the NAVI control unit is normal.
>> WORK END
CONFIGURATION (AROUND VIEW MONITOR CONTROL UNIT)
MANUAL SETTING ITEM
Detail
Items
Setting value
TRANSMISSION
MT
M/T models
CVT
CVT models
AT
A/T models
OTHER
Except for above
SOUND SYSTEM
BASE
—
BOSE
With BOSE system
BOSE SURROUND
With BOSE surround system
ROCKFORD FOSGATE
Without BOSE system without woof-
er
ROCKFORD SUB WOOFER
Without BOSE system with woofer
CAMERA SYSTEM
NONE
—
AVM
—
NONE/AVM
Without camera system or with
around view monitor system
REAR
With rear view monitor system
REAR+SIDE
With rear view monitor system and
front-side view monitor function
AVM+PA
With around view monitor system
and parking assist function
AV
INSPECTION AND ADJUSTMENT
AV-115
< BASIC INSPECTION >
[AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
CONFIGURATION (AROUND VIEW MONITOR CONTROL UNIT) : Work Procedure
INFOID:0000000012202514
1.
SAVING VEHICLE SPECIFICATION
CONSULT Configuration
Perform “Before Replace ECU”, and save the current vehicle specification in CONSULT.
Is the vehicle specification saved normally?
YES
>> GO TO 2.
NO
>> GO TO 4.
2.
REPLACE AROUND VIEW MONITOR CONTROL UNIT
Replace around view monitor control unit. Refer to
AV-190, "Removal and Installation"
>> GO TO 3.
3.
WRITING VEHICLE SPECIFICATION
CONSULT Configuration
Select “Configuration” or “After Replace ECU”, and write the vehicle specification saved in CONSULT to
around view monitor control unit.
>> GO TO 6.
4.
REPLACE AROUND VIEW MONITOR CONTROL UNIT
Replace around view monitor control unit. Refer to
AV-190, "Removal and Installation"
>> GO TO 5.
5.
WRITE VEHICLE SPECIFICATION
CONSULT Configuration
Select “WRITE CONFIGURATION - Instruction selection” and write in the following list at a around view monitor
control unit depending on a vehicle specification.
>> GO TO 6.
6.
PERFORM SELF-DIAGNOSIS
CONSULT Self Diagnostic Result
Perform self-diagnosis of CONSULT, and check whether or not DTC U1305 is detected.
Is DTC U1305 detected?
YES
>> GO TO 5.
NO
>> GO TO 7.
7.
OPERATION CHECK
Check that the operation of the around view monitor control unit and camera images (fixed guide lines and
predictive course lines) are normal.
>> WORK END
PREDICTIVE COURSE LINE CENTER POSITION ADJUSTMENT
Setting item
Detail
Items
Setting value
TRANSMISSION
A/T
CVT models
M/T
M/T models
AV-116
< BASIC INSPECTION >
[AUDIO WITH NAVIGATION]
INSPECTION AND ADJUSTMENT
PREDICTIVE COURSE LINE CENTER POSITION ADJUSTMENT : Description
INFOID:0000000012202515
Adjust the center position of the predictive course line of the rear view monitor if it is shifted. Refer to
"PREDICTIVE COURSE LINE CENTER POSITION ADJUSTMENT : Work Procedure"
PREDICTIVE COURSE LINE CENTER POSITION ADJUSTMENT : Work Procedure
INFOID:0000000012202516
1.
DRIVING
Drive the vehicle straight ahead 100 m (328.1 ft) or more at a speed of 30 km/h (18.6 MPH) or more.
>> END
CALIBRATING CAMERA IMAGE (AROUND VIEW MONITOR)
CALIBRATING CAMERA IMAGE (AROUND VIEW MONITOR) : Description
INFOID:0000000012202517
• Calibration must be performed after removing/replacing the cameras, removing parts (e.g. front grille, door
mirror, and others) mounted on the cameras, or replacing the Around view monitor control unit.
• The use of CONSULT is required to perform calibration or writing of calibration results to the Around view
monitor control unit.
• Align the white lines on the road near the vehicle at the boundary of each camera image by this camera cal-
ibration. The white lines far from the vehicle may not be aligned at the boundary of each camera image. The
farther the line, the greater the difference is.
• Calibrating camera image, refer to
AV-116, "CALIBRATING CAMERA IMAGE (AROUND VIEW MONITOR) :
CALIBRATING CAMERA IMAGE (AROUND VIEW MONITOR) : Work Procedure
INFOID:0000000012202518
CALIBRATION FLOWCHART
AV
INSPECTION AND ADJUSTMENT
AV-117
< BASIC INSPECTION >
[AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
Following the flowchart shown in the figure, perform the calibration.
NOTE:
View in the incomplete calibration state is indicated by “
” on the
around view monitor.
CALIBRATION PROCEDURE
1.
AROUND VIEW MONITOR SCREEN CONFIRMATION
JSNIA8055GB
JSNIA4606ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст