Nissan Juke F15. Instruction — part 1118
REAR SEAT
SE-37
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
2. Pull tether cover in direction indicated by the arrow as
shown in the figure. Remove tether cover.
3. Open seatback fastener (A) and remove seatback retainer
(B).
4. Use pincers, etc., to press up pawls as shown by the arrows
in the figure, and remove headrest holder from seatback.
CAUTION:
Before installing headrest holder check its orientation.
(front/rear and right/left)
2. Remove seatback lock knob finisher.
1. Rotate seatback lock knob counterclockwise. Remove seat-
back lock knob.
: Pawl
JMJIA4611ZZ
JMJIA4369ZZ
PIIB4084J
JMJIA4374ZZ
SE-38
< REMOVAL AND INSTALLATION >
REAR SEAT
2. Push up seatback lock knob finisher while pressing pawls
indicated by arrows as shown in the figure. Remove seat-
back lock finisher from seatback.
CAUTION:
When installing seatback lock knob finisher, check
front and rear orientation and be careful to install it nor-
mally.
3. Remove seatback trim and seatback pad from seatback frame.
4. Remove hog rings, and separate the seatback trim and seatback pad.
CAUTION:
Before performing separating operation, check the installation position of hog rings.
5. Remove seatback silencer from seatback frame.
6. Remove seatback lock assembly mounting bolts, and then remove seatback lock assembly from seatback
frame.
INSTALLATION
Note the following, and assemble in the reverse order of disassembly.
CAUTION:
Always install the hog ring in position.
SEATBACK HINGE
SEATBACK HINGE : Removal and Installation
INFOID:0000000012196888
CENTER HINGE
Removal
1. Remove seatback LH and RH from the vehicle.
SE-33, "SEATBACK : Removal and Installation"
.
2. Remove seat cushion from the vehicle.
SE-32, "SEAT CUSHION : Removal and Installation"
.
3. Remove center hinge mounting bolts, and then remove center hinge from the vehicle.
Installation
Note the following items, and install in the reverse order of removal.
CAUTION:
When installing center hinge, tighten mounting bolts to the specified torque according to the numeri-
cal order as shown in the figure
JMJIA4375ZZ
REAR SEAT
SE-39
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
1. Temporarily tighten mounting bolt (1).
2. Tighten mounting bolts in numerical order (2 and 3 as
shown in the figure) to the specified torque.
For the specified torque, refer to
SIDE HINGE
Removal
1. Remove seatback from the vehicle.
SE-33, "SEATBACK : Removal and Installation"
.
2. Remove side hinge mounting bolt, and then remove side hinge from luggage side lower finisher.
Installation
Installation is the reverse order of removal. Tighten bolts to the specified torque.
For the specified torque, refer to
.
SEATBACK STRIKER
SEATBACK STRIKER : Removal and Installation
INFOID:0000000012196889
REMOVAL
1. Remove seatback LH and RH from the vehicle.
SE-33, "SEATBACK : Removal and Installation"
.
2. Remove seat cushion from the vehicle.
SE-32, "SEAT CUSHION : Removal and Installation"
.
3. Remove side hinge from the vehicle.
SE-38, "SEATBACK HINGE : Removal and Installation"
.
4. Remove luggage side lower finisher from the vehicle.
INT-35, "LUGGAGE SIDE LOWER FINISHER : Removal and Installation"
.
5. Remove outer anchor mounting anchor bolt, and then remove outer anchor.
6. Remove mounting bolts or nuts of striker, and then remove striker from the vehicle.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
When installing striker, tighten mounting bolts or nuts to the specified torque according to the numer-
ical order as shown in the figure.
: Vehicle front
JMJIA4608ZZ
SE-40
< REMOVAL AND INSTALLATION >
REAR SEAT
1. Temporarily tighten mounting bolts in numerical order (1
and 2 as shown in the figure).
2. Tighten mounting bolts or nuts to the specified torque in
numerical order (3, 4, and 5 as shown in the figure).
For the specified torque, refer to
: Vehicle front
JMJIA4455GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст