Nissan Juke F15. Instruction — part 227
DLK-88
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
UNLOCK SENSOR
UNLOCK SENSOR
Component Function Check
INFOID:0000000012196656
1.
CHECK FUNCTION
1. Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2. Select “UNLK SEN -DR” in “DATA MONITOR” mode.
3. Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Unlock sensor is OK.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000012196657
1.
CHECK BCM OUTPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect front door lock assembly (driver side) connector.
3. Check signal between front door lock assembly (driver side) harness connector and ground using oscillo-
scope.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK UNLOCK SENSOR CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between BCM harness connector and front door lock assembly (driver side) harness
connector.
3. Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-94, "Removal and Installation"
Monitor item
Condition
Status
UNLK SEN -DR
Driver side door
Lock
OFF
Unlock
ON
(+)
(–)
Signal
(Reference value)
Front door lock assembly (driver side)
Connector
Terminal
D38
3
Ground
PKIB4960J
BCM
Front door lock assembly (driver side)
Continuity
Connector
Terminal
Connector
Terminal
M68
31
D38
3
Existed
BCM
Ground
Continuity
Connector
Terminal
M68
31
Not existed
UNLOCK SENSOR
DLK-89
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
NO
>> Repair or replace harness.
3.
CHECK UNLOCK SENSOR GROUND CIRCUIT
Check continuity between front door lock assembly (driver side) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK UNLOCK SENSOR
DLK-89, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace front door lock assembly (driver side).
5.
CHECK INTERMITTENT INCIDENT
GI-45, "Intermittent Incident"
.
>> INSPECTION END
Component Inspection
INFOID:0000000012196658
1.
CHECK UNLOCK SENSOR
1. Turn ignition switch OFF.
2. Disconnect front door lock assembly (driver side) connector.
3. Check continuity between front door lock assembly (driver side) terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace front lock assembly (driver side).
Front door lock assembly (driver side)
Ground
Continuity
Connector
Terminal
D38
4
Existed
Front door lock assembly (driver side)
Condition
Continuity
Terminal
3
4
Driver side door
Unlock
Existed
Lock
Not existed
DLK-90
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
DOOR DOES NOT LOCK/UNLOCK WITH DOOR LOCK AND UNLOCK SWITCH
SYMPTOM DIAGNOSIS
DOOR DOES NOT LOCK/UNLOCK WITH DOOR LOCK AND UNLOCK
SWITCH
ALL DOOR
ALL DOOR : Description
INFOID:0000000012196659
All doors do not lock/unlock using door lock and unlock switch.
ALL DOOR : Diagnosis Procedure
INFOID:0000000012196660
1.
CHECK DOOR LOCK AND UNLOCK SWITCH
Check door lock and unlock switch.
DLK-73, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK DOOR LOCK ACTUATOR
Check front door lock assembly (driver side).
DLK-68, "DRIVER SIDE : Component Function Check"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
REPLACE BCM
1. Replace BCM. Refer to
BCS-94, "Removal and Installation"
.
2. Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-45, "Intermittent Incident"
.
DRIVER SIDE
DRIVER SIDE : Description
INFOID:0000000012196661
Driver side door does not lock/unlock using door lock and unlock switch.
DRIVER SIDE : Diagnosis Procedure
INFOID:0000000012196662
1.
CHECK DOOR LOCK ACTUATOR
Check front door lock assembly (driver side).
DLK-68, "DRIVER SIDE : Component Function Check"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
REPLACE BCM
1. Replace BCM. Refer to
BCS-94, "Removal and Installation"
.
2. Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-45, "Intermittent Incident"
.
PASSENGER SIDE
DOOR DOES NOT LOCK/UNLOCK WITH DOOR LOCK AND UNLOCK SWITCH
DLK-91
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
PASSENGER SIDE : Description
INFOID:0000000012196663
Passenger side door does not lock/unlock using door lock and unlock switch.
PASSENGER SIDE : Diagnosis Procedure
INFOID:0000000012196664
1.
CHECK DOOR LOCK ACTUATOR
Check front door lock assembly (passenger side).
DLK-69, "PASSENGER SIDE : Component Function Check"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
REPLACE BCM
1. Replace BCM. Refer to
BCS-94, "Removal and Installation"
.
2. Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-45, "Intermittent Incident"
.
REAR LH
REAR LH : Description
INFOID:0000000012196665
Rear LH side door does not lock/unlock using door lock and unlock switch.
REAR LH : Diagnosis Procedure
INFOID:0000000012196666
1.
CHECK DOOR LOCK ACTUATOR
Check rear door lock assembly LH.
DLK-70, "REAR LH : Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
REPLACE BCM
1. Replace BCM. Refer to
BCS-94, "Removal and Installation"
.
2. Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-45, "Intermittent Incident"
.
REAR RH
REAR RH : Description
INFOID:0000000012196667
Rear RH side door does not lock/unlock using door lock and unlock switch.
REAR RH : Diagnosis Procedure
INFOID:0000000012196668
1.
CHECK DOOR LOCK ACTUATOR
Check rear door lock assembly RH.
DLK-71, "REAR RH : Component Function Check"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
REPLACE BCM
1. Replace BCM. Refer to
BCS-94, "Removal and Installation"
.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст