Nissan Juke F15. Instruction — part 1310
TM-430
< BASIC INSPECTION >
[CVT: RE0F10D]
ADDITIONAL SERVICE WHEN REPLACING TCM
2. Turn ignition switch ON.
Does the shift position indicator display “P” at the same time when turning ON the ignition switch?
YES
>> GO TO 6.
NO
>> Check harness between battery and TCM harness connector terminal. Refer to
6.
WRITE TCM DATA (VEHICLE SPECIFICATIONS)
With CONSULT
1. Select “Programming”.
2. Perform programming according to the CONSULT display.
>> WORK END
7.
DETECT MALFUNCTIONING ITEM
Check the following items:
• Harness between the TCM and the ROM assembly inside the transaxle assembly is open or shorted.
• Disconnected, loose, bent, collapsed, or otherwise abnormal connector housing terminals
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace the malfunctioning parts.
ADDITIONAL SERVICE WHEN REPLACING TRANSAXLE ASSEMBLY
TM-431
< BASIC INSPECTION >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
ADDITIONAL SERVICE WHEN REPLACING TRANSAXLE ASSEMBLY
Description
INFOID:0000000012201125
Perform the following work after the transaxle assembly is replaced. For work procedure, refer to
.
WRITING TCM DATA
• TCM performs accurate control by retrieving data (inherent characteristic value) of each solenoid. For this
reason, after replacing transaxle assembly, it is necessary to write new data in TCM.
ERASING OF CVT FLUID DEGRADATION LEVEL DATA
• TCM records the degradation level of the CVT fluid calculated from the vehicle driving status. Therefore, if
the transaxle assembly is replaced, it is necessary to erase the CVT fluid degradation level data recorded by
TCM.
Work Procedure
INFOID:0000000012201126
1.
CHECK THE SERIAL NUMBER
Write down the serial number of new transaxle assembly.
>> GO TO 2.
2.
WRITE TCM DATA (IP CHARACTERISTICS VALUE)
NOTE:
Write data of new solenoid in TCM according to the following instructions:
With CONSULT
CAUTION:
When the work is interrupted, obtain data again from the supplied CD.
1. Shift the selector lever to the P position.
2. Turn ignition switch OFF and wait for 10 seconds.
3. Turn ignition switch ON.
4. Insert the supplied CD into CONSULT.
5. Select “Work Support” in “TRANSMISSION”.
6. Select “WRITE IP CHARA - REPLACEMENT AT/CVT”.
7. Check that the serial number displayed on CONSULT screen and those written in the memo agree.
8. Write data in TCM according to the instructions on the CONSULT screen.
NOTE:
When writing is complete, the shift position indicator of the combination meter displays P.
>> GO TO 3.
JSDIA6075GB
TM-432
< BASIC INSPECTION >
[CVT: RE0F10D]
ADDITIONAL SERVICE WHEN REPLACING TRANSAXLE ASSEMBLY
3.
ERASE CVT FLUID DEGRADATION LEVEL DATA
With CONSULT
1. Select “WORK SUPPORT” in “TRANSMISSION”.
2. Select “CONFORM CVTF DETERIORTN”.
3. Touch “Clear”.
>> WORK END
ADDITIONAL SERVICE WHEN REPLACING TCM AND TRANSAXLE ASSEM-
BLY
TM-433
< BASIC INSPECTION >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
ADDITIONAL SERVICE WHEN REPLACING TCM AND TRANSAXLE AS-
SEMBLY
Description
INFOID:0000000012201127
When replacing TCM and transaxle assembly as a set, perform the following work. For work procedure, refer
to
TCM PROGRAMMING
• Since vehicle specifications are not yet written in a new TCM, it is necessary to write them with CONSULT.
CAUTION:
When replacing TCM, save TCM data on CONSULT before removing TCM.
WRITING TCM DATA
• TCM performs accurate control by retrieving data (inherent characteristic value) of each solenoid. For this
reason, after replacing TCM and transaxle assembly, it is necessary to write new data in TCM.
Work Procedure
INFOID:0000000012201128
1.
SAVE TCM DATA (VEHICLE SPECIFICATIONS)
With CONSULT
1. Turn ignition switch OFF.
2. Connect all of disconnected connectors.
3. Turn ignition switch ON.
4. Select “Re/programming, Configuration”.
5. Select “AT/CVT”.
NOTE:
If “AT/CVT” is not displayed and TCM data cannot be saved on CONSULT, GO TO 2.
6. Select “Programming”.
7. Save TCM data on CONSULT according to the CONSULT display.
>> GO TO 2.
2.
REPLACE TCM AND TRANSAXLE ASSEMBLY
1. Turn ignition switch OFF and wait for 10 seconds.
2. Replace TCM and transaxle assembly. Refer to
TM-554, "Removal and Installation"
(Transaxle assembly).
CAUTION:
Write down the serial number of new transaxle assembly.
>> GO TO 3.
JSDIA6075GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст