Nissan Juke F15. Instruction — part 1384
WW-32
< DTC/CIRCUIT DIAGNOSIS >
FRONT WIPER MOTOR HI CIRCUIT
FRONT WIPER MOTOR HI CIRCUIT
Component Function Check
INFOID:0000000012197055
1.
CHECK FRONT WIPER HI OPERATION
CONSULT ACTIVE TEST
1. Select “FRONT WIPER” of IPDM E/R active test item.
2. With operating the test item, check front wiper operation.
Is front wiper (HI) operation normally?
YES
>> Front wiper motor HI circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000012197056
1.
CHECK FRONT WIPER MOTOR (HI) OUTPUT VOLTAGE
CONSULT ACTIVE TEST
1. Turn ignition switch OFF.
2. Disconnect front wiper motor connector.
3. Turn ignition switch ON.
4. Select “FRONT WIPER” of IPDM E/R active test item.
5. With operating the test item, check voltage between front wiper motor harness connector and ground.
*: According to front wiper protection function, IPDM E/R supplies voltage for 10 seconds (battery voltage) and
then stops for 20 seconds (0 V). This operations occurs repeatedly.
Is the inspection result normal?
YES
>> Replace front wiper motor.
NO
>> GO TO 2.
2.
CHECK FRONT WIPER MOTOR (HI) CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check continuity between IPDM E/R harness connector and front wiper motor harness connector.
4. Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> Replace IPDM E/R.
NO
>> Repair or replace harness.
Hi
: Front wiper (HI) operation
Off
: Stop the front wiper.
(+)
(
−)
Condition
Voltage (Approx.)
Front wiper motor
Connector
Terminal
E20
1
Ground
FRONT WIPER
Hi
Battery voltage
(10 seconds*)
IPDM E/R
Front wiper motor
Continuity
Connector
Terminal
Connector
Terminal
E14
39
E20
1
Existed
IPDM E/R
Ground
Continuity
Connector
Terminal
E14
39
Not existed
FRONT WIPER STOP POSITION SIGNAL CIRCUIT
WW-33
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
FRONT WIPER STOP POSITION SIGNAL CIRCUIT
Component Function Check
INFOID:0000000012197057
1.
CHECK FRONT WIPER STOP POSITION SIGNAL
CONSULT DATA MONITOR
1. Select “WIP AUTO STOP” of IPDM E/R data monitor item.
2. Operate the front wiper.
3. With the front wiper operation, check the monitor status.
Is the status of item normal?
YES
>> Front wiper stop position signal circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000012197058
1.
CHECK IPDM E/R OUTPUT VOLTAGE
1. Turn ignition switch OFF.
2. Disconnect front wiper motor connector.
3. Turn ignition switch ON.
4. Check voltage between front wiper motor harness connector and ground.
Is the inspection result normal?
YES
>> Replace front wiper motor.
NO
>> GO TO 2.
2.
CHECK FRONT WIPER MOTOR CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check continuity between IPDM E/R harness connector and front wiper motor harness connector.
4. Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> Replace IPDM E/R.
NO
>> Repair or replace harness.
Monitor item
Condition
Monitor status
WIP AUTO STOP
Front wiper motor
Stop position
STOP P
Except stop position
ACT P
(+)
(
−)
Voltage (Approx.)
Front wiper motor
Connector
Terminal
E20
4
Ground
Battery voltage
IPDM E/R
Front wiper motor
Continuity
Connector
Terminal
Connector
Terminal
E13
25
E20
4
Existed
IPDM E/R
Ground
Continuity
Connector
Terminal
E13
25
Not existed
WW-34
< DTC/CIRCUIT DIAGNOSIS >
FRONT WIPER MOTOR GROUND CIRCUIT
FRONT WIPER MOTOR GROUND CIRCUIT
Diagnosis Procedure
INFOID:0000000012197059
1.
CHECK FRONT WIPER MOTOR GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect front wiper motor connector.
3. Check continuity between front wiper motor harness connector and ground.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Repair or replace harness.
Front wiper motor
Ground
Continuity
Connector
Terminal
E20
5
Existed
WASHER SWITCH
WW-35
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
WASHER SWITCH
Component Inspection
INFOID:0000000012197060
1.
CHECK WASHER SWITCH
1. Turn ignition switch OFF.
2. Disconnect combination switch connector.
3. Check continuity between the combination switch terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace combination switch (Wiper and washer switch).
A
: Terminal 4
B
: Terminal 6
C
: Terminal 3
D
: Terminal 1
JPLIA0164GB
Combination switch
Condition
Continuity
Terminal
3
4
Front washer switch ON
Existed
1
6
1
4
Rear washer switch ON
6
3
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст