Nissan Juke F15. Instruction — part 274
RING GEAR SHAFT
DLN-101
< UNIT DISASSEMBLY AND ASSEMBLY >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
• Measure the diameter (X) of transfer case with a pair of vernier
calipers. Refer to “Measuring point”.
CAUTION:
Never damage transfer case.
Dimension “Y” measurement
• Measure dimension (Y
′) of transfer case (including the thick-
ness of straightedge) with a pair of vernier calipers and
straightedge. Refer to “Measuring point”.
CAUTION:
Never damage transfer case.
• Measure the thickness of straightedge.
• Calculate the dimension “Y” by formula below.
Dimension “Z” measurement
• Measure dimension (Z) of transfer case with a pair of vernier
calipers and straightedge. Refer to “Measuring point”.
CAUTION:
Never damage transfer case.
Dimension “V” measurement
JSDIA2171ZZ
JSDIA2494ZZ
Y = Y
′ − “Thickness of straightedge”
JSDIA2543ZZ
JSDIA2174ZZ
DLN-102
< UNIT DISASSEMBLY AND ASSEMBLY >
[TRANSFER: TY21B]
RING GEAR SHAFT
• Measure dimension (V) of ring gear shaft with a pair of vernier
calipers. Refer to “Measuring point”.
Dimension “W” measurement
• Measure dimension (W) of ring gear shaft with a pair of vernier
calipers. Refer to “Measuring point”.
Dimension “E” measurement
• Measure dimension (E) of ring gear shaft with a pair of vernier
calipers. Refer to “Measuring point”.
Dimension “F” measurement
• Measure dimension (F) from outer race edge surface of ring
gear bearing (left) to inner race edge surface with depth
gauge. Refer to “Measuring point”.
Dimension “G” measurement
JSDIA2175ZZ
JSDIA2176ZZ
JSDIA2177ZZ
JSDIA2178ZZ
RING GEAR SHAFT
DLN-103
< UNIT DISASSEMBLY AND ASSEMBLY >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
• Measure thickness (G) of spacer (left) with a pair of vernier
calipers. Refer to “Measuring point”.
2. Calculate dimension “B” by the formula below.
3. Calculate dimension “D” by the formula below.
4. Check dimension (M) on the ring gear side face.
NOTE:
Dimension “M” indicates the difference between the optimum
engagement and standard dimensions in increments of 0.01 mm
(0.0004 in) written on the ring gear side face.
5. Calculate the thickness of the ring gear bearing adjusting shim
(left) “T
1
” by the formula below.
NOTE:
Calculate dimension “C” as 56.0 mm (2.20 in)
6. Select ring gear bearing adjusting shim (left).
For selection adjusting shim, refer to the latest parts information.
CAUTION:
• Only one adjusting shim can be selected.
• Select the closest one, favoring thicker over thinner when necessary if no adjusting shim with
the calculated value is available.
Ring gear bearing adjusting shim (right)
1. Measure the dimensions of each measuring point with the following procedure:
Dimension “X” measurement
• Measure the diameter (X) of transfer case with a pair of vernier
calipers. Refer to “Measuring point”.
CAUTION:
Never damage transfer case.
Dimension “Y” measurement
• Measure dimension (Y
′) of transfer case (including the thick-
ness of straightedge) with a pair of vernier calipers and
straightedge. Refer to “Measuring point”.
CAUTION:
Never damage transfer case.
B = Z
− Y − (X × 0.5)
D = E
− V + W
JSDIA2179ZZ
T
1
= A
− B + C + D − E − F − G − (M / 100) + 0.045 mm
(0.0018 in)
JSDIA2495ZZ
JSDIA2171ZZ
JSDIA2494ZZ
DLN-104
< UNIT DISASSEMBLY AND ASSEMBLY >
[TRANSFER: TY21B]
RING GEAR SHAFT
• Measure the thickness of straightedge.
• Calculate the dimension “Y” by formula below.
Dimension “Z” measurement
• Measure dimension (Z) of transfer case with a pair of vernier
calipers and straightedge. Refer to “Measuring point”.
CAUTION:
Never damage transfer case.
Dimension “H” measurement
• Measure dimension (H) from outer race edge surface of ring
gear bearing (right) to inner race edge surface with depth
gauge. Refer to “Measuring point”.
Dimension “I” measurement
• Measure thickness (I) of spacer (right) with a pair of vernier
calipers. Refer to “Measuring point”.
2. Calculate dimension “B” by the formula below.
3. Calculate dimension “D” by the formula below.
Y = Y
′ − “Thickness of straightedge”
JSDIA2543ZZ
JSDIA2174ZZ
JSDIA2180ZZ
B = Z
− Y − (X × 0.5)
D = E
− V + W
JSDIA2181ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст