Nissan Juke F15. Instruction — part 1369
ADDITIONAL SERVICE WHEN REPLACING BCM
WT-19
< BASIC INSPECTION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
ADDITIONAL SERVICE WHEN REPLACING BCM
Description
INFOID:0000000012201845
When replacing BCM, tire pressure sensor ID registration is required. Refer to
Work Procedure
INFOID:0000000012201846
1.
PERFORM TIRE PRESSURE SENSOR ID REGISTRATION
Perform tire pressure sensor ID registration.
>> Refer to
.
WT-20
< BASIC INSPECTION >
TIRE PRESSURE SENSOR ID REGISTRATION
TIRE PRESSURE SENSOR ID REGISTRATION
Description
INFOID:0000000012201847
This procedure must be done after replacing or rotating wheels, replacing tire pressure sensor or BCM. Refer
to
Work Procedure
INFOID:0000000012201848
1.
TIRE PRESSURE SENSOR ID REGISTRATION PROCEDURE
CAUTION:
To perform ID registration, observe the following points:
• Never register ID in a place where radio waves are interfered (e.g. radio tower).
• Never register ID in a place close to vehicles including TPMS.
With CONSULT
1. Display the “WORK SUPPORT” screen and select “ID REGIST”.
Is the tire pressure sensor activation tool (J-50190 or J-45295-A) used for the tire pressure sensor ID registra-
tion procedure?
YES
>> GO TO 2.
NO
>> GO TO 3.
2.
TIRE PRESSURE SENSOR ID REGISTRATION PROCEDURE (WITH TIRE PRESSURE SENSOR ACTI-
VATION TOOL)
1. Turn the ignition switch ON.
2. Select the start button on the “ID REGIST” screen.
3. Contact the tire pressure sensor activation tool (J-50190 or J-
45295-A) (1) to the side of the tire at the location to the tire pres-
sure sensor.
4. Press and hold the tire pressure sensor activation tool button
while pushing the tool to the tire surface. (approximately for 5
seconds)
CAUTION:
Perform the ID registration procedure starting from the
vehicle front left wheel, then repeat the procedure in the
order of the front right wheel, rear right wheel, and rear left
wheel.
5. When ID registration is completed, check the following pattern at each wheel.
6. After the ID registration procedure for all wheels is completed, press “END” to end ID registration, and
check that ID registration for all wheels is completed.
Is the check result normal?
YES
>> ID registration END.
NO
>> Refer to
3.
TIRE PRESSURE SENSOR ID REGISTRATION PROCEDURE (WITHOUT TIRE PRESSURE SENSOR
ACTIVATION TOOL)
1. Adjust the tire pressure for all wheels to match the list below.
NNEIC0020ZZ
Sequence
ID registration position
Turn signal lamp
CONSULT
1
Front left wheel
2 blinks
“Red”
↓
“Green”
2
Front right wheel
3
Rear right wheel
4
Rear left wheel
TIRE PRESSURE SENSOR ID REGISTRATION
WT-21
< BASIC INSPECTION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
2. Drive the vehicle at a speed at more than 40 km/h (25 MPH) for 3 minutes or more, then perform the tire
pressure sensor ID registration procedure.
3. After ID registration for all wheels is completed, press “END” to end ID registration.
4. Adjust the tire pressures for all wheels to the specified value. Refer to
.
Is ID registrations for all wheels completed?
YES
>> ID registration END.
NO
>> Performs trouble-diagnosis of the Tire Pressure Monitoring System (TPMS). Refer to
Tire position
Tire pressure kPa (kg/cm
2
, psi)
Front LH
240 (2.4, 35)
Front RH
220 (2.2, 31)
Rear RH
200 (2.0, 29)
Rear LH
180 (1.8, 26)
ID registration position
CONSULT
Front LH
“Red”
↓
“Green”
Front RH
Rear RH
Rear LH
WT-22
< DTC/CIRCUIT DIAGNOSIS >
C1704, C1705, C1706, C1707 LOW TIRE PRESSURE
DTC/CIRCUIT DIAGNOSIS
C1704, C1705, C1706, C1707 LOW TIRE PRESSURE
DTC Logic
INFOID:0000000012201849
DTC DETECTION LOGIC
*:182.7 kPa (1.9 kg/cm
2
, 26 psi) [Standard air pressure is for 230 kPa (2.3 kg/cm
2
,33 psi) vehicles.]
*:189.6 kPa (1.9 kg/cm
2
, 27 psi) [Standard air pressure is for 240 kPa (2.4 kg/cm
2
,35 psi) vehicles.]
*:196.5 kPa (2.0 kg/cm
2
, 28 psi) [Standard air pressure is for 250 kPa (2.5 kg/cm
2
,36 psi) vehicles.]
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION
With CONSULT
1. Turn the ignition switch ON.
CAUTION:
Never start the engine.
2. Check the tire pressure for all wheels and adjust to the specified value. Refer to
.
3. Perform self-diagnosis for “AIR PRESSURE MONITOR”.
Is DTC “C1704”, “C1705”, “C1706”, or “C1707” detected?
YES
>> Proceed to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000012201850
1.
TIRE PRESSURE SENSOR ID REGISTRATION
Perform tire pressure sensor ID registration. Refer to
Is tire pressure sensor ID registration completed?
YES
>> GO TO 2.
NO
>> Replace applicable tire pressure sensor. Refer to
WT-41, "Removal and Installation"
2.
CHECK TIRE PRESSURE
Check the air pressure of all wheels. Refer to
.
CAUTION:
If the checked value is close to the standard, reduce the tire pressure, and then with the ignition
switch ON, adjust the tire pressure again so that it is within the standard.
Is the inspection result normal?
YES
>> Perform “DTC CONFIRMATION PROCEDURE” (self-diagnosis) again. Refer to
.
NO
>> After adjusting the air pressure, GO TO 3
3.
CHECK TIRE PRESSURE SIGNAL
With CONSULT
1. Select “DATA MONITOR” in “AIR PRESSURE MONITOR” of “BCM”.
2. Check that the tire pressures match the standard value.
DTC
Display Item
Malfunction detected condition
Possible causes
C1704
LOW PRESSURE FL
Front LH tire pressure drops to * kPa (* kg/cm
2
, * psi) or less.
Low tire pressure
C1705
LOW PRESSURE FR
Front RH tire pressure drops to * kPa (* kg/cm
2
, * psi) or less.
C1706
LOW PRESSURE RR
Rear RH tire pressure drops to * kPa (* kg/cm
2
, * psi) or less.
C1707
LOW PRESSURE RL
Rear LH tire pressure drops to * kPa (* kg/cm
2
, * psi) or less.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст