Nissan Juke F15. Instruction — part 240
DLK-140
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
REAR DOOR
REAR DOOR
Exploded View
INFOID:0000000012196716
DOOR ASSEMBLY
DOOR ASSEMBLY : Removal and Installation
INFOID:0000000012196717
CAUTION:
• Perform work with 2 workers, because of it’s heavy weight.
• When removing and installing rear door assembly, support door with a jack and shop cloth to pro-
tect door and body.
REMOVAL
1.
Rear door panel
2.
TORX bolt
3.
Door striker
4.
Door check link
5.
Door hinge (lower)
6.
Door hinge (upper)
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
: N·m (kg-m, ft-lb)
: Body grease
JMKIA5880GB
REAR DOOR
DLK-141
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
1. Remove rear door harness grommet (2) from body side outer
(1), and then pull out rear door harness.
2. Disconnect rear door harness connector.
3. Remove mounting bolt of door check link on the vehicle.
4. Remove door hinge mounting bolts (door side), and then remove rear door assembly.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Apply anticorrosive agent onto the mounting surface.
• Check rear door open/close, lock/unlock operation after installation.
• Check door hinge rotating part for poor lubrication. If necessary, apply body grease.
• After installation, perform the fitting adjustment. Refer to
DLK-142, "DOOR ASSEMBLY : Adjust-
• After installation, apply touch-up paint (the body color) onto the head of door hinge mounting nuts.
JMKIA5881ZZ
JMKIA5882ZZ
DLK-142
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
REAR DOOR
DOOR ASSEMBLY : Adjustment
INFOID:0000000012196718
Check the clearance and surface height between front door and each part by visually and touching.
If the clearance and the surface height are out of specification, adjust them according to the procedures
shown below.
Unit: mm (in)
FITTING ADJUSTMENT PROCEDURE
1. Remove center pillar lower garnish. Refer to
INT-22, "CENTER PILLAR LOWER GARNISH : Removal
1.
Front fender
2.
Front door
3.
Rear door
4.
Body side outer
5.
Door striker
6.
TORX bolt
7.
Front door hinge
8.
Rear door hinge (upper)
9.
Rear door hinge (lower)
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
: Body grease
Portion
Clearance
Surface height
Front door – Rear door
B – B
3.3 – 5.3 (0.130 – 0.209)
(-1.0) – (+1.0) [(-0.039) – (+0.039)]
Rear door – Body side outer
C – C
2.6 – 4.6 (0.102 – 0.181)
(-1.0) – (+1.0) [(-0.039) – (+0.039)]
JMKIA5638GB
REAR DOOR
DLK-143
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
2. Loosen door hinge mounting nuts on door side.
3. Adjust the surface height of rear door according to the fitting standard dimension.
4. Temporarily tighten door hinge mounting nuts on door side.
5. Loosen door hinge mounting nuts and bolts on body side.
6. Raise rear door at rear end to adjust clearance of rear door according to the fitting standard dimension.
7. After adjustment tighten bolts and nuts to the specified torque.
CAUTION:
• After installation, apply touch-up paint (the body color) onto the head of hinge mounting bolts
and nuts.
• Check door hinge rotating part for poor lubrication. If necessary, apply body grease.
8. Install center pillar lower garnish. Refer to
INT-22, "CENTER PILLAR LOWER GARNISH : Removal and
.
DOOR STRIKER ADJUSTMENT
Adjust door striker so that it becomes parallel with door lock insertion direction.
DOOR STRIKER
DOOR STRIKER : Removal and Installation
INFOID:0000000012196719
REMOVAL
Remove TORX bolts, and then remove door striker.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Check rear door open/close, lock/unlock operation after installation.
• After installation, be sure to perform the fitting adjustment. Refer to
DOOR HINGE
DOOR HINGE : Removal and Installation
INFOID:0000000012196720
CAUTION:
• Perform work with 2 workers, because of it’s heavy weight.
• When removing and installing rear door assembly, support door with a jack and shop cloth to pro-
tect door and body.
REMOVAL
1. Remove rear door assembly. Refer to
DLK-140, "DOOR ASSEMBLY : Removal and Installation"
2. Remove center pillar lower garnish. Refer to
INT-22, "CENTER PILLAR LOWER GARNISH : Removal
3. Remove rear door hinge mounting bolts and nuts (body side), and then remove door hinge.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Apply anticorrosive agent onto the mounting surface.
• Check rear door open/close operation after installation.
• When removing and installing rear door assembly, perform the fitting adjustment. Refer to
.
• After installing, apply the touch-up paint (the body color) onto the head of door hinge mounting nuts.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст