Nissan Juke F15. Instruction — part 321
ECM
EC-97
< ECU DIAGNOSIS INFORMATION >
[MR FOR NISMO RS MODELS]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
CLSD THL POS
Ignition switch: ON
(Engine stopped)
Accelerator pedal: Fully released
ON
Accelerator pedal: Slightly depressed
OFF
AIR COND SIG
Engine: After warming up, idle the
engine
Air conditioner switch: OFF
OFF
Air conditioner switch: ON
(Compressor operates.)
ON
PW/ST SIGNAL
Engine: After warming up, idle the
engine
Steering wheel: Not being turned
OFF
Steering wheel: Being turned
ON
LOAD SIGNAL
Ignition switch: ON
Rear window defogger switch: ON
and/or Lighting switch: 2nd position
ON
Rear window defogger switch and lighting
switch: OFF
OFF
IGNITION SW
Ignition switch: ON
→ OFF → ON
ON
→ OFF → ON
HEATER FAN SW
Engine: After warming up, idle the
engine
Heater fan switch: ON
ON
Heater fan switch: OFF
OFF
BRAKE SW
Ignition switch: ON
Brake pedal: Fully released
OFF
Brake pedal: Slightly depressed
ON
IGN TIMING
• Engine: After warming up
• Selector lever: P or N (CVT),
Neutral (M/T)
• Air conditioner switch: OFF
• No load
Idle
5
° - 15° BTDC
2,000 rpm
30
° - 50° BTDC
COMBUSTION
—
These items are displayed
but are not applicable to this
model.
CAL/LD VALUE
• Engine: After warming up
• Selector lever: P or N (CVT),
Neutral (M/T)
• Air conditioner switch: OFF
• No load
Idle
5 - 35 %
2,500 rpm
5 - 35 %
MASS AIRFLOW
• Engine: After warming up
• Selector lever: P or N (CVT),
Neutral (M/T)
• Air conditioner switch: OFF
• No load
Idle
1.0 - 5.0 g/s
2,500 rpm
2.0 - 10.0 g/s
PURG VOL C/V
• Engine: After warming up
• Selector lever: P or N (CVT),
Neutral (M/T)
• Air conditioner switch: OFF
• No load
Idle
(Accelerator pedal: Not depressed even
slightly, after engine starting.)
0 - 10 %
2,000 rpm
0 - 20 %
INT/V TIM(B1)
• Engine: After warming up
• Selector lever: P or N (CVT),
Neutral (M/T)
• Air conditioner switch: OFF
• No load
Idle
−5° - 5°CA
2,000 rpm
Approx. 0
° - 20°CA
EXH/V TIM B1
• Engine: After warming up
• Selector lever: P or N (CVT),
Neutral (M/T)
• Air conditioner switch: OFF
• No load
Idle
−5° - 5°CA
Around 2,500 rpm while the engine speed
is rising
Approx. 0
° - 30°CA
INT/V SOL(B1)
• Engine: After warming up
• Selector lever: P or N (CVT),
Neutral (M/T)
• Air conditioner switch: OFF
• No load
Idle
0 %
2,000 rpm
Approx. 0% - 60 %
Monitor Item
Condition
Values/Status
EC-98
< ECU DIAGNOSIS INFORMATION >
[MR FOR NISMO RS MODELS]
ECM
AIR COND RLY
Engine: After warming up, idle the
engine
Air conditioner switch: OFF
OFF
Air conditioner switch: ON
(Compressor operates)
ON
VENT CONT/V
Ignition switch: ON
OFF
FUEL PUMP RLY
• For 1 seconds after turning ignition switch: ON
• Engine running or cranking
ON
Except above
OFF
THRTL RELAY
Ignition switch: ON
ON
HO2S2 HTR (B1)
• Engine speed: Below 3,600 rpm after the following conditions are met.
- Engine: After warming up
- Keeping the engine speed between 3,500 and 4,000 rpm for 1 minute and at
idle for 1 minute under no load
ON
Engine speed: Above 3,600 rpm
OFF
ALT DUTY SIG
Power generation voltage variable control: Operating
ON
Power generation voltage variable control: Not operating
OFF
I/P PULLY SPD
Vehicle speed: More than 20 km/h (12 MPH)
Almost the same speed as
the tachometer indication
VEHICLE SPEED
Turn drive wheels and compare CONSULT value with the speedometer indica-
tion.
Almost the same speed as
the speedometer indication
IDL A/V LEARN
Engine: running
Idle air volume learning has not been per-
formed yet.
YET
Idle air volume learning has already been
performed successfully.
CMPLT
TRVL AFTER MIL
Ignition switch: ON
Vehicle has traveled after MIL has illumi-
nated.
0 - 65,535 km (0 - 40,723
miles)
ENG OIL TEMP
Engine: After warming up
More than 70
°C (158°F)
A/F S1 HTR(B1)
Engine: After warming up, idle the engine
(More than 140 seconds after starting engine)
4 - 100 %
SET VHCL SPD
Engine: Running
ASCD: Operating
The preset vehicle speed is
displayed
MAIN SW
Ignition switch: ON
MAIN switch: Pressed
ON
MAIN switch: Released
OFF
CANCEL SW
Ignition switch: ON
CANCEL switch: Pressed
ON
CANCEL switch: Released
OFF
RESUME/ACC SW
Ignition switch: ON
ACCEL/RES switch: Pressed
ON
ACCEL/RES switch: Released
OFF
SET SW
Ignition switch: ON
COAST/SET switch: Pressed
ON
COAST/SET switch: Released
OFF
BRAKE SW1
(Brake pedal posi-
tion switch)
Ignition switch: ON
Brake pedal: Fully released
ON
Brake pedal: Slightly depressed
OFF
BRAKE SW2
(Stop lamp switch)
Ignition switch: ON
Brake pedal: Fully released
OFF
Brake pedal: Slightly depressed
ON
VHCL SPD CUT
Ignition switch: ON
NON
LO SPEED CUT
Ignition switch: ON
NON
AT OD MONITOR
Ignition switch: ON
OFF
AT OD CANCEL
Ignition switch: ON
OFF
CRUISE LAMP
Ignition switch: ON
MAIN switch: Pressed at the 1st time
→
at the 2nd time
ON
→ OFF
Monitor Item
Condition
Values/Status
ECM
EC-99
< ECU DIAGNOSIS INFORMATION >
[MR FOR NISMO RS MODELS]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
SET LAMP
NOTE:
The item is indicated, but not used.
FAN DUTY
Engine: Running
0 - 100 %
ALT DUTY
Engine: Idle
0 - 80 %
BAT CUR SEN
• Engine speed: Idle
• Battery: Fully charged
*2
• Selector lever: P or N (CVT), Neutral (M/T)
• Air conditioner switch: OFF
• No load
Approx. 2,600 - 3,500 mV
A/F ADJ-B1
Engine: Running
−0.450 - 0.330
P/N POSI SW
Ignition switch: ON
Selector lever: P or N (CVT), Neutral (M/
T)
ON
Selector lever: Except above
OFF
INT/A TEMP SE
Ignition switch: ON
Indicates intake air tempera-
ture
AC PRESS SEN
• Engine: Idle
• Both A/C switch and blower fan switch: ON (Compressor operates)
1.0 - 4.0 V
FUEL PRES SEN
• Engine: After warming up
• Selector lever: P or N (CVT),
Neutral (M/T)
• Air conditioner switch: OFF
• No load
Idle
Approx. 2.74 MPa
2,000 rpm
Approx. 3.0 MPa
TURBO BST SEN
• Engine speed: Idle
• Selector lever: D (CVT), Neutral
(M/T)
• Fuel: Premium gasoline
• The accelerator pedal is depressed to
a half stroke position or more.
• The readings of boost in the multi-func-
tion meter are the same as the ambient
pressure or more.
• Engine speed: More than 3,000 rpm
3.07 - 3.15 V
• Engine speed: Idle
• Selector lever: D (CVT), Neutral
(M/T)
• Fuel: Regular gasoline
• The accelerator pedal is depressed to
a half stroke position or more.
• The readings of boost in the multi-func-
tion meter are the same as the ambient
pressure or more.
• Engine speed: More than 3,000 rpm
2.91 - 2.99 V
ATOM PRES SEN
Ignition switch: ON
1.80 - 4.80 V
FUEL INJ TIM
• Engine: After warming up
• Selector lever: P or N (CVT),
Neutral (M/T)
• Air conditioner switch: OFF
• No load
Idle
Approx. 30 deg
2,000 rpm
Approx. 30 deg
FUEL INJ B1
• Engine: After warming up
• Selector lever: P or N (CVT),
Neutral (M/T)
• Air conditioner switch: OFF
• No load
Idle
Approx. 0.8 msec
2,000 rpm
Approx. 1.1 msec
EVAP LEAK DIAG
Ignition switch: ON
Indicates the condition of
EVAP leak diagnosis.
EVAP DIAG READY
Ignition switch: ON
Indicates the ready condition
of EVAP leak diagnosis.
BAT TEMP SEN
• Engine: After warming up
• Selector lever: P or N (CVT),
Neutral (M/T)
• Air conditioner switch: OFF
• No load
Idle
Indicates the temperature
around the battery.
THRTL STK CNT B1
NOTE:
The item is indicated, but not used.
—
Monitor Item
Condition
Values/Status
EC-100
< ECU DIAGNOSIS INFORMATION >
[MR FOR NISMO RS MODELS]
ECM
HO2 S2 DIAG1(B1)
DTC P0139 self-diagnosis (delayed response) has not been performed yet.
INCMP
DTC P0139 self-diagnosis (delayed response) has already been performed suc-
cessfully.
CMPLT
HO2 S2 DIAG2(B1)
DTC P0139 self-diagnosis (slow response) has not been performed yet.
INCMP
DTC P0139 self-diagnosis (slow response) has already been performed suc-
cessfully.
CMPLT
H/P FUEL PUMP
DEG
• Engine: After warming up
• Selector lever: P or N (CVT),
Neutral (M/T)
• Air conditioner switch: OFF
• No load
Idle
Approx. 255 - 275 deg
2,000 rpm
Approx. 255 - 275 deg
FUEL PRES SEN V
• Engine: After warming up
• Selector lever: P or N (CVT),
Neutral (M/T)
• Air conditioner switch: OFF
• No load
Idle
Approx. 1,140 - 1,460 mV
Revving engine from idle to 4,000 rpm
quickly
Approx. 1,300 - 2,900 mV
EOP SENSOR
• Engine: After warming up
• Selector lever: P or N (CVT),
Neutral (M/T)
• Air conditioner switch: OFF
• No load
Idle
Approx. 1,450 mV
2,000 rpm
Approx. 2,850 mV
ECM TEMP 1
• Engine: After cooling
• Ignition switch: ON
Indicates the temperature
around the ECM.
ECM TEMP 2
• Engine: After cooling
• Ignition switch: ON
Indicates the temperature
around the ECM.
BOOST S/V DUTY
Engine: After warming up
Idle
0 %
• The accelerator pedal is depressed to
a half stroke position or more.
• Engine speed: Below 3,000 rpm
100 %
• The accelerator pedal is depressed to
a half stroke position or more.
• Engine speed: More than 3,000 rpm
30 - 60 %
G SENSOR
Vehicle is level
Approx. 2,500 mV
A/F SEN1 DIAG1
(B1)
DTC P015A and P015B self-diagnosis is incomplete.
INCMP
DTC P015A and P015B self-diagnosis is complete.
CMPLT
A/F SEN1 DIAG2
(B1)
DTC P014C and P014D self-diagnosis is incomplete.
INCMP
DTC P014C and P014D self-diagnosis is complete.
CMPLT
A/F SEN1 DIAG3
(B1)
The vehicle condition is not within the diagnosis range of DTC P014C, P014D,
P015A or P015B.
ABSNT
The vehicle condition is within the diagnosis range of DTC P014C, P014D,
P015A or P015B.
PRSNT
A/F-S ATMSPHRC
CRCT B1
Engine: After warming up, idle the engine
Varies depending on vehicle
environment.
A/F-S ATMSPHRC
CRCT B2
Engine: After warming up, idle the engine
Varies depending on vehicle
environment.
A/F-S ATMSPHRC
CRCT UP B1
Engine: Running
Varies depending on the
number of updates.
A/F-S ATMSPHRC
CRCT UP B2
Engine: Running
Varies depending on the
number of updates.
SYSTEM 1 DIAG-
NOSIS A B1
DTC P219A self-diagnosis is incomplete.
INCMP
DTC P219A self-diagnosis is complete.
CMPLT
SYSTEM 1 DIAG-
NOSIS B B1
DTC P219A self-diagnosis is on standby.
ABSENT
DTC P219A self-diagnosis is under diagnosis.
PRSENT
Monitor Item
Condition
Values/Status
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст