Nissan Juke F15. Instruction — part 623
EM-46
< REMOVAL AND INSTALLATION >
[MR FOR NISMO RS MODELS]
OIL PAN (LOWER)
OIL PAN (LOWER)
Exploded View
INFOID:0000000012197271
1.
O-ring
2.
Oil pan (upper)
3.
Oil level gauge guide
4.
O-ring
5.
Oil level gauge
6.
Oil pump drive chain
7.
Crankshaft sprocket
8.
Oil pump sprocket
9.
Oil pump chain tensioner
10. Oil pump
11. Drain plug
12. Drain plug washer
13. Oil pan (lower)
14. Oil filter
15. Connector bolt
16. Clamp 17. Water
hose
18. Oil
cooler
19. Crankshaft position sensor
20. Gasket
21. Oil pan bolt
22. Rear oil seal
A.
Comply with the assembly proce-
dure when tightening. Refer to
B.
To thermostat hosing
C.
To thermostat housing (M/T models)
To CVT oil warmer (CVT models)
D.
Oil pan side
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
: Always replace after every disassembly.
: Sealing point
JPBIA4875GB
OIL PAN (LOWER)
EM-47
< REMOVAL AND INSTALLATION >
[MR FOR NISMO RS MODELS]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
Removal and Installation
INFOID:0000000012197272
REMOVAL
1. Drain engine oil. Refer to
.
2. Remove oil pan (lower) with the following procedure:
a. Loosen mounting bolts in reverse order as shown in the figure.
NOTE:
Disregard the numerical order No.7 and No.11 in removal.
b. Insert seal cutter [SST: KV10111100 (J-37228)] (A) between oil
pan (upper) and oil pan (lower).
CAUTION:
• Never damage the mating surface.
• Never insert a screwdriver. This damages the mating sur-
faces.
c. Slide the seal cutter [SST: KV10111100 (J-37228)] by tapping on
the side of tool with a hammer.
d. Remove oil pan (lower).
INSTALLATION
CAUTION:
Do not reuse drain plug washer.
1. Install oil pan (lower) as follows:
a. Use a scraper (A) to remove old liquid gasket from mating sur-
faces.
• Also remove old liquid gasket from mating surface of oil pan
(upper).
• Remove old liquid gasket from the bolt holes and threads.
CAUTION:
Never scratch or damage the mating surface when cleaning
off old liquid gasket.
: Should be lubricated with oil.
: Indicates that the parts is connected at points with same symbols in actual vehicle.
: Engine front
JPBIA4364GB
JPBIA4365ZZ
JPBIA4366ZZ
EM-48
< REMOVAL AND INSTALLATION >
[MR FOR NISMO RS MODELS]
OIL PAN (LOWER)
b. Apply a continuous bead of liquid gasket (A) with a tube presser
(commercial service tool) as shown in the figure.
Use Genuine RTV Silicon Sealant or equivalent. Refer to
22, "Recommended Chemical Products and Sealants"
CAUTION:
Attaching should be done within 5 minutes after liquid gas-
ket application.
c.
Tighten bolts in numerical order as shown in the figure.
NOTE:
• Tighten bolts the No.1 and No.2 in two steps.
• The numerical order No.7 and No.11 shows the second steps.
2. Install oil pan drain plug.
CAUTION:
Do not reuse drain plug washer.
• Refer to the figure of components of former page for installation direction of drain plug washer. Refer to
.
3. Install in the reverse order of removal after this step.
Inspection
INFOID:0000000012197273
INSPECTION AFTER REMOVAL
Clean oil strainer if any object attached.
INSPECTION AFTER INSTALLATION
1. Check the engine oil level and adjust engine oil. Refer to
2. Start engine, and check there is no leakage of engine oil.
3. Stop engine and wait for 10 minutes.
4. Check the engine oil level again. Refer to
.
1
: Oil pan (lower)
b
: 7.5 - 9.5 mm (0.295 - 0.374 in)
c
:
φ 4.0 - 5.0 mm (0.157 - 0.197 in)
: Engine outside
: Engine front
JPBIA4367ZZ
: Engine front
JPBIA4364GB
HIGH PRESSURE FUEL PUMP AND FUEL HOSE
EM-49
< REMOVAL AND INSTALLATION >
[MR FOR NISMO RS MODELS]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
HIGH PRESSURE FUEL PUMP AND FUEL HOSE
Exploded View
INFOID:0000000012197274
CAUTION:
Never remove or disassemble parts unless instructed as shown in the figure.
Removal and Installation
INFOID:0000000012197275
REMOVAL
WARNING:
EM-8, "Precaution for Handling High Pressure Fuel System"
when working on the
high pressure fuel system.
• Put a “CAUTION: FLAMMABLE” sign in the workshop.
• Be sure to work in a well ventilated area and furnish workshop with a CO
2
fire extinguisher.
1.
High pressure fuel pump insulator
2.
High pressure fuel pump
3.
O-ring
4.
High pressure fuel pump lifter
5.
Fuel rail connector
6.
Fuel tube
7.
Bracket
8.
Fuel pump connector protector
9.
Fuel feed hose
A.
To centralized under-floor piping
: Engine front
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
: Always replace after every disassembly.
: Should be lubricated with oil.
: Indicates that the parts is connected at points with same symbols in actual vehicle.
JSBIA1672GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст