Nissan Juke F15. Instruction — part 758
REAR BUMPER
EXT-23
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
Removal and Installation
INFOID:0000000012199313
CAUTION:
Bumper fascia is made of resin. Never apply strong force to it, and be careful to prevent contact with
oil.
REMOVAL
1. Fully open back door.
2. Remove bumper fascia fixing screws of rear combination lamp lower side (LH and RH).
3. Remove rear fillet molding rear side. Refer to
EXT-37, "REAR FILLET MOLDING : Removal and Installa-
4. Remove bumper closing (LH and RH).
5. Remove fixing clips of bumper lower side.
6. Remove bumper fascia fixing screws (A) (LH and RH).
7. Pull bumper fascia side toward the vehicle side to disengage the
fitting of bumper side bracket and bumper fascia side according
to the numerical order 1
→3 as shown by the arrows in the fig-
ure.
CAUTION:
When removing bumper fascia, 2 workers are required so
as to prevent it from dropping.
8. Remove bumper fascia.
9. Remove the following parts after removing bumper fascia.
• Reflex reflector (LH and RH). Refer to
EXL-116, "Removal and Installation"
.
• Bumper fascia lower
• Rear fog lamp housing (NISMO and NISMO RS). Refer to
EXL-115, "Removal and Installation"
10. Remove bumper energy absorber.
11. Remove bumper reinforcement mounting nuts, and then remove bumper reinforcement.
12. Remove rear panel lower.
13. Remove bumper side bracket fixing screws, and then remove bumper side bracket (LH and RH).
INSTALLATION
Note the following items, and then install in the reverse order of removal.
NOTE:
• The following table shows the specified values for checking normal installation status.
• Fitting adjustment cannot be performed.
: Pawl
: Always replace after every disassembly.
, , , , , , :
Indicates
that
the
part
is
connected
at points with same symbol in actual vehicle.
JMKIA5561ZZ
: Pawl
JMKIA5564ZZ
EXT-24
< REMOVAL AND INSTALLATION >
REAR BUMPER
Except for NISMO and NISMO RS
NISMO and NISMO RS
JMKIB4687ZZ
Portion
Clearance
Surface height difference
Bumper fascia assembly –
Rear fender
A – A
0.3 – 1.1 mm
(0.012 – 0.043 in)
(
−0.3) – (+1.7) mm
[(
−0.012) – (+0.067) in]
Bumper fascia assembly –
Rear combination lamp
B – B
0.2 – 2.8 mm
(0.008 – 0.110 in)
—
Bumper fascia assembly –
Back door
C – C
3.0 – 7.0 mm
(0.118 – 0.276 in)
0.0 – 4.0 mm
(0.000 – 0.157 in)
D – D
6.0 – 10.0 mm
(0.236 – 0.394 in)
—
JMKIB4688ZZ
Portion
Clearance
Surface height difference
Bumper fascia assembly –
Rear fender
A – A
0.0 – 1.0 mm
(0.000 – 0.039 in)
(
−0.3) – (+1.7) mm
[(
−0.012) – (+0.067) in]
Bumper fascia assembly –
Rear combination lamp
B – B
0.2 – 3.0 mm
(0.008 – 0.118 in)
—
Bumper fascia assembly –
Back door
C – C
3.0 – 7.0 mm
(0.118 – 0.276 in)
0.0 – 4.0 mm
(0.000 – 0.157 in)
D – D
6.0 – 10.0 mm
(0.236 – 0.394 in)
0.0 – 4.0 mm
(0.000 – 0.157 in)
FRONT GRILLE
EXT-25
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
FRONT GRILLE
Exploded View
INFOID:0000000012199314
EXCEPT FOR NISMO AND NISMO RS
NISMO AND NISMO RS
1.
Bumper fascia
2.
Front side grille RH
3.
Front center grille
4.
Emblem
5.
Front side grille LH
: Pawl
: Indicates that the part is connected at points with same symbol in actual vehicle.
JMKIB4175ZZ
EXT-26
< REMOVAL AND INSTALLATION >
FRONT GRILLE
Removal and Installation
INFOID:0000000012199315
REMOVAL
Except for NISMO and NISMO RS
1. Fully open hood assembly.
2. Remove front center grille upper fixing clips (A).
CAUTION:
Apply protective tape (B) around bumper fascia.
1.
Bumper fascia
2.
Front upper grille
3.
Front grille
4.
Front grille emblem
5.
Emblem
: Pawl
, , : Indicates that the part is connected at points with same symbol in actual vehicle.
JMKIB4689ZZ
JMKIA5623ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст