Nissan Juke F15. Instruction — part 952
LAN
A-BAG BRANCH LINE CIRCUIT
LAN-145
< DTC/CIRCUIT DIAGNOSIS >
[CAN SYSTEM (TYPE 6)]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
A-BAG BRANCH LINE CIRCUIT
Diagnosis Procedure
INFOID:0000000012200613
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes
or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK CONNECTOR
1. Turn the ignition switch OFF.
2. Disconnect the battery cable from the negative terminal.
3. Check the terminals and connectors of the air bag diagnosis sensor unit for damage, bend and loose con-
nection (unit side and connector side).
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace the main harness.
2.
CHECK AIR BAG DIAGNOSIS SENSOR UNIT
Check the air bag diagnosis sensor unit. Refer to
Is the inspection result normal?
YES
>> Replace the main harness.
NO
>> Replace parts whose air bag system has a malfunction.
LAN-146
< DTC/CIRCUIT DIAGNOSIS >
[CAN SYSTEM (TYPE 6)]
AVM BRANCH LINE CIRCUIT
AVM BRANCH LINE CIRCUIT
Diagnosis Procedure
INFOID:0000000012200614
1.
CHECK CONNECTOR
1. Turn the ignition switch OFF.
2. Disconnect the battery cable from the negative terminal.
3. Check the terminals and connectors of the around view monitor control unit for damage, bend and loose
connection (unit side and connector side).
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair the terminal and connector.
2.
CHECK HARNESS FOR OPEN CIRCUIT
1. Disconnect the connector of around view monitor control unit.
2. Check the resistance between the around view monitor control unit harness connector terminals.
Is the measurement value within the specification?
YES
>> GO TO 3.
NO
>> Repair the around view monitor control unit branch line.
3.
CHECK POWER SUPPLY AND GROUND CIRCUIT
Check the power supply and the ground circuit of the around view monitor control unit. Refer to
"AROUND VIEW MONITOR CONTROL UNIT : Diagnosis Procedure"
.
Is the inspection result normal?
YES (Present error)>>Replace the around view monitor control unit. Refer to
AV-190, "Removal and Installa-
.
YES (Past error)>>Error was detected in the around view monitor control unit branch line.
NO
>> Repair the power supply and the ground circuit.
Around view monitor control unit harness connector
Resistance (
Ω)
Connector No.
Terminal No.
M98
26
24
Approx. 54 – 66
LAN
HVAC BRANCH LINE CIRCUIT
LAN-147
< DTC/CIRCUIT DIAGNOSIS >
[CAN SYSTEM (TYPE 6)]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
HVAC BRANCH LINE CIRCUIT
Diagnosis Procedure
INFOID:0000000012200615
1.
CHECK CONNECTOR
1. Turn the ignition switch OFF.
2. Disconnect the battery cable from the negative terminal.
3. Check the terminals and connectors of the A/C auto amp. for damage, bend and loose connection (unit
side and connector side).
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair the terminal and connector.
2.
CHECK HARNESS FOR OPEN CIRCUIT
1. Disconnect the connector of A/C auto amp.
2. Check the resistance between the A/C auto amp. harness connector terminals.
Is the measurement value within the specification?
YES
>> GO TO 3.
NO
>> Repair the A/C auto amp. branch line.
3.
CHECK POWER SUPPLY AND GROUND CIRCUIT
Check the power supply and the ground circuit of the A/C auto amp. Refer to
.
Is the inspection result normal?
YES (Present error)>>Replace the A/C auto amp. Refer to
HAC-93, "Removal and Installation"
.
YES (Past error)>>Error was detected in the A/C auto amp. branch line.
NO
>> Repair the power supply and the ground circuit.
A/C auto amp. harness connector
Resistance (
Ω)
Connector No.
Terminal No.
M50
6
7
Approx. 54 – 66
LAN-148
< DTC/CIRCUIT DIAGNOSIS >
[CAN SYSTEM (TYPE 6)]
AV BRANCH LINE CIRCUIT
AV BRANCH LINE CIRCUIT
Diagnosis Procedure
INFOID:0000000012200616
1.
CHECK CONNECTOR
1. Turn the ignition switch OFF.
2. Disconnect the battery cable from the negative terminal.
3. Check the terminals and connectors of the NAVI control unit for damage, bend and loose connection (unit
side and connector side).
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair the terminal and connector.
2.
CHECK HARNESS FOR OPEN CIRCUIT
1. Disconnect the connector of NAVI control unit.
2. Check the resistance between the NAVI control unit harness connector terminals.
Is the measurement value within the specification?
YES
>> GO TO 3.
NO
>> Repair the NAVI control unit branch line.
3.
CHECK POWER SUPPLY AND GROUND CIRCUIT
Check the power supply and the ground circuit of the NAVI control unit. Refer to
.
Is the inspection result normal?
YES (Present error)>>Replace the NAVI control unit. Refer to
AV-182, "Removal and Installation"
YES (Past error)>>Error was detected in the NAVI control unit branch line.
NO
>> Repair the power supply and the ground circuit.
NAVI control unit harness connector
Resistance (
Ω)
Connector No.
Terminal No.
M108
8
17
Approx. 54 – 66
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст