Nissan Juke F15. Instruction — part 177
CL-12
< REMOVAL AND INSTALLATION >
CLUTCH PEDAL
Note the following, and install in the reverse order of removal.
CAUTION:
Press master cylinder rod end into clutch pedal until it stops.
Inspection and Adjustment
INFOID:0000000012199550
INSPECTION AFTER REMOVAL
• Check clutch pedal for bend, damage, or a cracked weld. If bend, damage, or a cracked weld is found,
replace clutch pedal.
• Check stopper rubber and pedal stopper rubber. If damage or deformation is found, replace stopper rubber
and pedal stopper rubber.
• Check pedal pad. If wear or damage is found, replace pedal pad.
INSPECTION AFTER INSTALLATION
• Check the clutch pedal height, clutch pedal height at clutch disengagement, and clutch pedal play. Refer to
CL-6, "Inspection and Adjustment"
• Check the clutch interlock switch position. Refer to
CL-6, "Inspection and Adjustment"
.
• Check the clutch pedal position switch position. Refer to
CL-6, "Inspection and Adjustment"
ADJUSTMENT AFTER INSTALLATION
• Adjust the clutch interlock switch position. Refer to
CL-6, "Inspection and Adjustment"
.
• Adjust the clutch pedal position switch position. Refer to
CLUTCH MASTER CYLINDER
CL-13
< REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
CL
N
O
P
CLUTCH MASTER CYLINDER
Exploded View
INFOID:0000000012199551
Removal and Installation
INFOID:0000000012199552
REMOVAL
CAUTION:
• Keep painted surface on the body or other parts free of clutch fluid. If it spills, wipe up immediately
and wash the affected area with water.
• Never disassemble clutch master cylinder.
1. Drain clutch fluid. Refer to
.
2. Remove air cleaner case. Refer to
EM-192, "Removal and Installation"
(Except for NISMO RS),
(For NISMO RS).
3. Remove reservoir hose from reservoir tank and master cylinder.
4. Remove master cylinder rod end (
) from clutch pedal.
1.
Reservoir hose
2.
Reservoir tank
3.
Master cylinder
JPDIB0162ZZ
PCIB1491E
CL-14
< REMOVAL AND INSTALLATION >
CLUTCH MASTER CYLINDER
5. Pull up the lock pin (1) from connector of master cylinder (2) and
separate clutch tube (3).
6. Rotate master cylinder clockwise by 45 degrees, and then
remove master cylinder from the vehicle.
INSTALLATION
CAUTION:
Keep painted surface on the body or other parts free of clutch fluid. If it spills, wipe up immediately
and wash the affected area with water.
1. Tilt master cylinder clockwise by 45 degrees (A) and insert it to
the mounting hole. Rotate counterclockwise and secure it. At
this time, nipple (1) is upward of the vehicle.
2. Install master cylinder rod end to clutch pedal.
CAUTION:
Press master cylinder rod end into clutch pedal until it
stops.
3. Install reservoir hose to reservoir tank and master cylinder.
CAUTION:
Set reservoir hose with painted mark facing upward.
4. Press down the lock pin into connector of master cylinder until it stops.
5. Install clutch tube into connector of master cylinder until it stops.
6. For the next step and after, install in the reverse order of removal.
Inspection and Adjustment
INFOID:0000000012199553
INSPECTION AFTER INSTALLATION
• Check the fluid leakage and the fluid level. Refer to
.
• Check the clutch pedal height, clutch pedal height at clutch disengagement, and clutch pedal play. Refer to
CL-6, "Inspection and Adjustment"
• Check the clutch interlock switch position. Refer to
CL-6, "Inspection and Adjustment"
.
• Check the clutch pedal position switch position. Refer to
CL-6, "Inspection and Adjustment"
ADJUSTMENT AFTER INSTALLATION
• Adjust the clutch interlock switch position. Refer to
CL-6, "Inspection and Adjustment"
.
• Adjust the clutch pedal position switch position. Refer to
CL-6, "Inspection and Adjustment"
• Perform the air bleeding. Refer to
JPDIB0167ZZ
B
: Mounting condition
JPDIB0114ZZ
CLUTCH PIPING
CL-15
< REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
CL
N
O
P
CLUTCH PIPING
Exploded View
INFOID:0000000012199554
Hydraulic Layout
INFOID:0000000012199555
Removal and Installation
INFOID:0000000012199556
CAUTION:
Keep painted surface on the body or other parts free of clutch fluid. If it spills, wipe up immediately
and wash the affected area with water.
REMOVAL
Note the following, and refer to
• Drain clutch fluid. Refer to
.
1.
CSC (Concentric Slave Cylinder)
2.
Clip (Except for NISMO RS)
3.
Clutch tube
4.
Clutch damper
5.
Bracket
6.
Master cylinder
JSDIA3642ZZ
1.
Clutch tube
2.
Lock pin
3.
CSC (Concentric Slave Cylinder)
4.
Clutch damper
5.
Master cylinder
6.
Clutch pedal
PCIB1499E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст