Nissan Juke F15. Instruction — part 1169
B0002 DRIVER AIR BAG MODULE
SRC-41
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
2. Disconnect driver air bag module harness connector and combination switch (spiral cable) harness con-
nector.
3. Check continuity between spiral cable terminals.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Replace spiral cable. Refer to
SR-15, "Removal and Installation"
7.
CHECK SPIRAL CABLE CIRCUIT 4
Check continuity between spiral cable terminals.
Is the inspection result normal?
YES
>> GO TO 9.
NO
>> Replace spiral cable. Refer to
SR-15, "Removal and Installation"
8.
REPLACE SPIRAL CABLE
1. Replace spiral cable. Refer to
GI-45, "Intermittent Incident"
.
2. Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 9.
NO
>> INSPECTION END
9.
REPLACE DRIVER AIR BAG MODULE
1. Replace driver air bag module. Refer to
SR-12, "Removal and Installation"
.
2. Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 10.
NO
>> INSPECTION END
10.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to
SR-29, "Removal and Installation"
2. Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
Terminal
Continuity
12
9
Not existed
Terminal
Continuity
29
30
Not existed
SRC-42
< DTC/CIRCUIT DIAGNOSIS >
B0010 PASSENGER AIR BAG MODULE
B0010 PASSENGER AIR BAG MODULE
DTC Description
INFOID:0000000012199594
DTC DETECTION LOGIC
POSSIBLE CAUSE
[B0010–09, B0010–1A]
• Connection malfunction or short circuit of harness and connector
• Internal malfunction of passenger air bag module
• Internal malfunction of air bag diagnosis sensor unit
[B0010–11]
• Connection malfunction or short circuit to ground of harness and connector
• Internal malfunction of passenger air bag module
• Internal malfunction of air bag diagnosis sensor unit
[B0010–12]
• Connection malfunction or short circuit to power supply of harness and connector
• Internal malfunction of passenger air bag module
• Internal malfunction of air bag diagnosis sensor unit
[B0010–13]
• Connection malfunction or open circuit of harness and connector
• Internal malfunction of passenger air bag module
• Internal malfunction of air bag diagnosis sensor unit
FAIL-SAFE
—
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1. Turn ignition switch ON.
2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1. Turn ignition switch ON.
2. Check the air bag warning lamp status. Refer to
SRC-10, "On Board Diagnosis Function"
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO-1 >> To check malfunction symptom before repair: Refer to
GI-45, "Intermittent Incident"
.
NO-2 >> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000012199595
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
DTC
CONSULT screen items
(Trouble diagnosis content)
DTC detecting condition
B0010–09
ASSIST A/B MODULE
[Passenger Frontal Stage
1 Deployment Control
(Subfault)]
[SHORT]
Passenger air bag module circuits are shorted to each other
B0010–11
[GND-SHORT]
Passenger air bag module circuit is shorted to ground
B0010–12
[VB-SHORT]
Passenger air bag module circuit is shorted to power supply circuit
B0010–13
[OPEN]
Passenger air bag module circuit is open
B0010–1A
[SHORT]
Passenger air bag module circuits are shorted to each other
B0010 PASSENGER AIR BAG MODULE
SRC-43
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector for disconnection, looseness or damage.
Is the inspection result normal?
YES
>> GO TO 2.
NO–1 >> Damage: Replace malfunctioning harness and connector.
NO–2 >> Disconnection or looseness: Securely lock the connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace malfunctioning harness and connector.
3.
REPLACE PASSENGER AIR BAG MODULE
1. Replace passenger air bag module. Refer to
SR-18, "Removal and Installation"
2. Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to
SR-29, "Removal and Installation"
2. Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
SRC-44
< DTC/CIRCUIT DIAGNOSIS >
B0011 PASSENGER AIR BAG MODULE
B0011 PASSENGER AIR BAG MODULE
DTC Description
INFOID:0000000012199596
DTC DETECTION LOGIC
POSSIBLE CAUSE
[B0011–09, B0011–1A]
• Connection malfunction or short circuit of harness and connector
• Internal malfunction of passenger air bag module
• Internal malfunction of air bag diagnosis sensor unit
[B0011–11]
• Connection malfunction or short circuit to ground of harness and connector
• Internal malfunction of passenger air bag module
• Internal malfunction of air bag diagnosis sensor unit
[B0011–12]
• Connection malfunction or short circuit to power supply of harness and connector
• Internal malfunction of passenger air bag module
• Internal malfunction of air bag diagnosis sensor unit
[B0011–13]
• Connection malfunction or open circuit of harness and connector
• Internal malfunction of passenger air bag module
• Internal malfunction of air bag diagnosis sensor unit
FAIL-SAFE
—
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1. Turn ignition switch ON.
2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1. Turn ignition switch ON.
2. Check the air bag warning lamp status. Refer to
SRC-10, "On Board Diagnosis Function"
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO-1 >> To check malfunction symptom before repair: Refer to
GI-45, "Intermittent Incident"
.
NO-2 >> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000012199597
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
DTC
CONSULT screen items
(Trouble diagnosis content)
DTC detecting condition
B0011–09
ASSIST A/B MODULE 2
[Passenger Frontal Stage
2 Deployment Control
(Subfault)]
[SHORT]
Passenger air bag module circuits are shorted to each other
B0011–11
[GND-SHORT]
Passenger air bag module circuit is shorted to ground
B0011–12
[VB-SHORT]
Passenger air bag module circuit is shorted to power supply circuit
B0011–13
[OPEN]
Passenger air bag module circuit is open
B0011–1A
[SHORT]
Passenger air bag module circuits are shorted to each other
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст