Nissan Juke F15. Instruction — part 1101
REAR SHOCK ABSORBER
RSU-25
< REMOVAL AND INSTALLATION >
[AWD]
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
Note the following, and install in the reverse order of removal.
• To install bushings (1), securely insert protrusion (A) into the hole
on the vehicle body side.
• Install washer (1) in the direction shown in the figure.
• Perform final tightening of bolts and nuts at the shock absorber
lower side (rubber bushing), under unladen conditions with tires on
level ground.
• Hold a head (A) of shock absorber piston rod nut to have it rotate,
then tighten the piston rod lock nut (1) to the specified torque.
CAUTION:
Never reuse piston rod lock nut.
• When installing the cap, securely engage the cap groove (A) with
the flange on the vehicle side.
• Perform inspection after installation. Refer to
• After replacing the shock absorber, always follow the disposal pro-
cedure to discard the shock absorber. Refer to
Inspection
INFOID:0000000012200414
INSPECTION AFTER REMOVAL
Shock Absorber
Check the following items, and replace the part if necessary.
• Shock absorber for deformation, cracks, and other damage.
• Piston rod for damage, uneven wear, and distortion.
• Oil leakage.
JPEIB0240ZZ
: Bushing side
JPEIB0248ZZ
JPEIB0241ZZ
JPEIB0244ZZ
RSU-26
< REMOVAL AND INSTALLATION >
[AWD]
REAR SHOCK ABSORBER
Bound Bumper, Bushing
Check for cracks and damage. Replace it if necessary.
Washer, Bound Bumper Cover, Distance Tube
• Check for cracks and damage. Replace it if necessary.
INSPECTION AFTER INSTALLATION
1. Check wheel alignment. Refer to
2. Adjust neutral position of steering angle sensor. Refer to
.
Disposal
INFOID:0000000012200415
1. Set shock absorber horizontally to the ground with the piston rod fully extracted.
2. Drill 2 – 3 mm (0.08 – 0.12 in) hole at the position ( ) from top
as shown in the figure to release gas gradually.
CAUTION:
• Wear eye protection (safety glasses).
• Wear gloves.
• Be careful with metal chips or oil blown out by the com-
pressed gas.
NOTE:
• Drill vertically in this direction.
• Directly to the outer tube avoiding brackets.
• The gas is clear, colorless, odorless, and harmless.
3. Position the drilled hole downward and drain oil by moving the piston rod several times.
CAUTION:
Dispose of drained oil according to the law and local regulations.
A
: 20 – 30 mm (0.79 – 1.18 in)
JPEIA0161ZZ
COIL SPRING
RSU-27
< REMOVAL AND INSTALLATION >
[AWD]
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
COIL SPRING
Exploded View
INFOID:0000000012200416
Removal and Installation
INFOID:0000000012200417
REMOVAL
1. Remove tires with power tool. Refer to
WT-39, "Removal and Installation"
.
2. Remove wheel sensor and sensor harness. Refer to
BRC-150, "REAR WHEEL SENSOR : Removal and
.
3. Set jack under suspension arm.
CAUTION:
• Never damage the suspension arm with a jack.
• Check the stable condition when using a jack.
4. Separate rear shock absorber lower side form suspension arm. Refer to
RSU-24, "Removal and Installa-
5. Separate upper link from suspension arm.
6. Slowly lower jack, then remove upper rubber seat, coil spring and lower rubber seat from suspension arm.
CAUTION:
Operate while checking that jack supporting status is stable.
7. Perform inspection after removal. Refer to
INSTALLATION
Note the following, and install in the reverse order of removal.
1.
Upper rubber seat
2.
Coil spring
3.
Lower rubber seat
4.
Suspension arm
: Vehicle front
JPEIB0258ZZ
RSU-28
< REMOVAL AND INSTALLATION >
[AWD]
COIL SPRING
• Install the lower rubber seat a projection (A) is attached as suspen-
sion arm mounting hole (B).
• Match up lower rubber seat indentions and suspension arm
grooves and attach.
• Install coil spring (1) lower end with spring end holding section (B)
of lower rubber seat (2).
• Mach up coil spring (1) upper end to the centre of upper rubber
seat (2) projection (A) as shown in figure.
• Perform inspection after installation. Refer to
Inspection
INFOID:0000000012200418
INSPECTION AFTER REMOVAL
Check rubber seat and coil spring for deformation, crack, and damage. Replace it if necessary.
INSPECTION AFTER INSTALLATION
1. Check wheel sensor harness for proper connection. Refer to
.
2. Check wheel alignment. Refer to
3. Adjust neutral position of steering angle sensor. Refer to
.
JPEIB0261ZZ
Dimension (A)
: 10 mm (0.20 in) or less
JSEIA0943ZZ
JSEIA0944ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст