Nissan Juke F15. Instruction — part 803
FSU-10
< REMOVAL AND INSTALLATION >
FRONT COIL SPRING AND STRUT
• After replacing the strut absorber, always follow the disposal procedure to discard the strut absorber. Refer
Disassembly and Assembly
INFOID:0000000012199118
DISASSEMBLY
CAUTION:
Never damage strut assembly piston rod when removing components from strut assembly.
1. Install strut attachment (A) [SST: ST35652000 ( — )] to strut
assembly and secure it in a vise.
CAUTION:
When installing the strut attachment to strut assembly,
wrap a shop cloth around strut to protect from damage.
2. Using a spring compressor (A) (commercial service tool), com-
press coil spring between spring upper seat and lower seat
(strut assembly) until coil spring with a spring compressor is
free.
CAUTION:
Be sure a spring compressor is securely attached to coil
spring. Compress coil spring.
3. Check coil spring with a spring compressor between spring
upper seat and lower seat (strut assembly) is free. And then
remove piston rod lock nut while securing the piston rod tip so
that piston rod does not turn.
4. Remove mounting insulator, mounting bearing, and bound
bumper from strut.
5. After removing coil spring with a spring compressor (commercial service tool), then gradually release a
spring compressor.
CAUTION:
Loosen while making sure coil spring attachment position does not move.
6. Remove lower rubber seat.
7. Remove strut attachment [SST: ST35652000 ( — )] from strut assembly.
8. Perform inspection after disassembly. Refer to
ASSEMBLY
CAUTION:
Never damage strut assembly piston rod when installing components from strut assembly.
1. Install strut attachment [SST: ST35652000 ( — )] to strut and secure it in a vise.
CAUTION:
When installing the strut attachment to strut assembly, wrap a shop cloth around strut to protect
from damage.
2. Install lower rubber seat.
3. Compress coil spring using a spring compressor (commercial service tool), and install it onto strut assem-
bly.
CAUTION:
• Be sure a compressor is securely attached to coil spring. Compress coil spring.
JPEIA0006ZZ
JPEIA0007ZZ
FRONT COIL SPRING AND STRUT
FSU-11
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
• Be careful with the vertical direction of the coil spring.
• Set coil spring so that its paint (A) mark is aligned with the
position of 1.75 turns from the bottom end of the coil
spring.
• Align the lower end of coil spring (1) with (A) of lower rub-
ber seat (2) as shown in the figure.
4. Apply soapy water to bound bumper.
CAUTION:
Never use machine oil.
5. Insert bound bumper into mounting insulator.
6. Install mounting bearing.
CAUTION:
Never apply oils, such as grease, when installing the
mounting bearing.
7. Check the location of identification mark (A) of the mounting
insulator and install it with the arrow (B) faced outside of the
vehicle to the strut.
NOTE:
The identification mark "0" shows right mounting insulator and
"1" shows left.
8. Secure piston rod tip so that piston rod does not turn, then
tighten piston rod lock nut with specified torque.
CAUTION:
Never reuse piston rod lock nut.
9. Gradually release a spring compressor (A) (commercial service
tool), and remove coil spring.
CAUTION:
Loosen while making sure coil spring attachment position
does not move.
: Upper side
JSEIA0940ZZ
Dimension (B)
: 5 mm (0.20 in) or less
JSEIA0942ZZ
JPEIA0246ZZ
JPEIA0007ZZ
FSU-12
< REMOVAL AND INSTALLATION >
FRONT COIL SPRING AND STRUT
10. Remove the strut attachment (A) [SST: ST35652000 ( — )]
from strut assembly.
Inspection
INFOID:0000000012199119
INSPECTION AFTER DISASSEMBLY
Check the following items, and replace the parts if necessary.
Strut
• Strut for deformation, cracks or damage.
• Piston rod for damage, uneven wear or distortion.
• Oil leakage.
Strut Mounting Insulator and bound bumper
Check strut mounting insulator and bound bumper for cracks, wear or damage.
Coil Spring
Check coil spring for cracks, wear or damage.
INSPECTION AFTER INSTALLATION
1. Check wheel sensor harness for proper connector. Refer to
BRC-147, "FRONT WHEEL SENSOR :
.
2. Check wheel alignment. Refer to
.
3. Adjust neutral position of steering angle sensor. Refer to
.
Disposal
INFOID:0000000012199120
1. Set strut assembly horizontally to the ground with the piston rod fully extracted.
2. Drill 2 – 3 mm (0.08 – 0.12 in) hole at the position ( ) from top
as shown in the figure to release gas gradually.
CAUTION:
• Wear eye protection (safety glasses).
• Wear gloves.
• Be careful with metal chips or oil blown out by the com-
pressed gas.
NOTE:
• Drill vertically in this direction.
• Directly to the outer tube avoiding brackets.
• The gas is clear, colorless, odorless, and harmless.
3. Position the drilled hole downward and drain oil by moving the piston rod several times.
CAUTION:
Dispose of drained oil according to the law and local regulations.
JPEIA0006ZZ
A
: 20 – 30 mm (0.79 – 1.18 in)
JPEIA0160ZZ
TRANSVERSE LINK
FSU-13
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
TRANSVERSE LINK
Exploded View
INFOID:0000000012199121
Removal and Installation
INFOID:0000000012199122
REMOVAL
1. Remove tires with power tool. Refer to
WT-39, "Removal and Installation"
.
2. Remove transverse link from steering knuckle. Refer to
(NISMO RS),
(EXCEPT NISMO RS).
3. Remove transverse link from suspension member.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Never reuse transverse link mounting nut.
• Perform final tightening of bolts and nuts at the vehicle installation position (rubber bushing), under unladen
conditions with tires on level ground.
• Perform inspection after installation. Refer to
.
Inspection
INFOID:0000000012199123
INSPECTION AFTER REMOVAL
Check the following items, and replace the parts if necessary.
Transverse Link
• Transverse link and bushing for deformation, cracks or damage.
• Ball joint boot for cracks or other damage, and also for grease leakage.
Swing Torque
1. Instructionly move ball stud to confirm it moves smoothly with no binding.
2. Move ball stud at least ten times by hand to check for smooth movement.
1.
Front suspension member
2.
Transverse link
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
JPEIA0242GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст