Nissan Juke F15. Instruction — part 836
NOISE
HA-27
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
J
K
L
M
A
B
HA
N
O
P
NOISE
Symptom Table
INFOID:0000000012197121
Symptom
Noise source
Probable cause
Corrective action
Unusual noise from compressor
when A/C is ON.
Inside of compressor
Wear, breakage, or clogging of foreign
material in inner parts.
Check compressor oil. Re-
fer to
.
Magnet clutch
Contact of clutch disc with pulley.
Check clearance between
clutch disc and pulley. Refer
to
Compressor body
Loosened compressor mounting bolts.
Check bolts for tightness.
Refer to
Unusual noise from cooler piping.
Cooler piping (pipe and
flexible hose)
Improper installation of clip and brack-
et.
Check the installation condi-
tion of the cooler piping. Re-
fer to
Unusual noise from expansion
valve when A/C is ON.
Expansion valve
Shortage of refrigerant.
• Check for leakage.
• Collect all refrigerant,
evacuate refrigerant cycle
again, and then refill it
with the specified amount
of refrigerant.
Wear, breakage, or clogging of foreign
material in inner parts.
Eliminate foreign material
from expansion valve, or re-
place it.
Unusual noise from belt.
—
Loosened belt
Check belt tension. Refer to
(MR for
NISMO RS models) or
(MR ex-
cept for NISMO RS mod-
els).
Internal compressor parts get locked
Replace compressor.
HA-28
< REMOVAL AND INSTALLATION >
COMPRESSOR
REMOVAL AND INSTALLATION
COMPRESSOR
Exploded View
INFOID:0000000012197122
REMOVAL
DISASSEMBLY
Type of bolt with flange
1.
Compressor
: N·m (kg-m, ft-lb)
JSIIA1870GB
JSIIA1806GB
1.
Compressor unit
2.
Field coil
3.
Snap ring
4.
Pulley assembly
5.
Snap ring
6.
Shim
7.
Clutch disc
: N·m (kg-m, ft-lb)
COMPRESSOR
HA-29
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
J
K
L
M
A
B
HA
N
O
P
Type of bolt without flange
COMPRESSOR
COMPRESSOR : Removal and Installation
INFOID:0000000012197123
CAUTION:
Perform lubricant return operation before each refrigeration system disassembly. However, if a large
amount of refrigerant or lubricant is detected, never perform lubricant return operation. Refer to
21, "Perform Lubricant Return Operation"
REMOVAL
1. Use a refrigerant collecting equipment (for HFC-134a) to discharge the refrigerant. Refer to
2. Remove drive belt. Refer to
EM-20, "Removal and Installation"
(MR except for NISMO RS models).
3. Remove mounting bolts (A), and then disconnect low-pressure
flexible hose (1) and high-pressure flexible hose (2).
CAUTION:
Cap or wrap the joint of the A/C piping and compressor with
suitable material such as vinyl tape to avoid the entry of air.
JMIIA0802GB
1.
Compressor unit
2.
Field coil
3.
Snap ring
4.
Pulley assembly
5.
Snap ring
6.
Shim
7.
Clutch disc
: N·m (kg-m, ft-lb)
: Vehicle front
JMIIA0947ZZ
HA-30
< REMOVAL AND INSTALLATION >
COMPRESSOR
4. Disconnect magnet clutch harness connector.
5. Remove mounting bolts. Pull out compressor in the direction
indicated by an arrow as shown in the figure to remove.
CAUTION:
Be careful not to contact with and damage surrounding
parts when removing compressor from the vehicle.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Replace O-rings with new ones. Then apply compressor oil to them when installing.
• Perform lubricant adjusting procedure before installing new compressor. Refer to
Adjusting Procedure for Compressor Replacement"
.
• Check for leakages when recharging refrigerant. Refer to
• Check tension of the drive belt after installing compressor. Refer to
MAGNET CLUTCH
MAGNET CLUTCH : Removal and Installation of Compressor Clutch
INFOID:0000000012197124
REMOVAL
Overhaul
1. Fix clutch disc.
2. Remove center bolt, and then remove clutch disc.
3. Remove snap ring using external snap ring pliers.
4. Position center pulley puller on the end of the drive shaft, and remove pulley assembly using any commer-
cially available pulley puller.
To prevent pulley groove from being deformed, puller claws should be positioned into the edge of the pul-
ley assembly.
5. Disconnect harness connector from compressor unit.
6. Remove snap ring using external snap ring pliers, and then remove field coil.
INSTALLATION
: Vehicle front
JMIIA0948ZZ
JMIIA1038ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст