Nissan Juke F15. Instruction — part 1009
MWI-58
< DTC/CIRCUIT DIAGNOSIS >
A/C AUTO AMP. CONNECTION RECOGNITION SIGNAL CIRCUIT
A/C AUTO AMP. CONNECTION RECOGNITION SIGNAL CIRCUIT
Diagnosis Procedure
INFOID:0000000012201340
1.
CHECK A/C AUTO AMP. CONNECTION RECOGNITION SIGNAL
1. Turn ignition switch ON.
2. Check voltage between combination meter harness connector and ground.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 2.
2.
CHECK A/C AUTO AMP. CONNECTION RECOGNITION SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect combination meter connector and A/C auto amp. connector.
3. Check continuity between combination meter harness connector and A/C auto amp. harness connector.
4. Check continuity between combination meter harness connector and ground.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Repair harness or connector.
Terminals
Voltage
(Approx.)
(+)
(
−)
Combination meter
Ground
Connector
Terminal
M34
31
5 V
Combination meter
A/C auto amp.
Continuity
Connector
Terminal
Connector
terminal
M34
31
M50
9
Existed
Combination meter
Ground
Continuity
Connector
Terminal
M34
31
Not existed
MWI
THE FUEL GAUGE INDICATOR DOES NOT OPERATE
MWI-59
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
SYMPTOM DIAGNOSIS
THE FUEL GAUGE INDICATOR DOES NOT OPERATE
Description
INFOID:0000000012201341
Fuel gauge will not indicate from a certain position.
Diagnosis Procedure
INFOID:0000000012201342
1.
CONDUCTING THE COMBINATION METER SELF-DIAGNOSIS MODE
Perform the self-diagnosis mode of combination meter, and then check that the fuel gauge operates normally.
MWI-21, "On Board Diagnosis Function"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace combination meter. Refer to
MWI-64, "Removal and Installation"
2.
CHECK FLOAT INTERFERENCE
Check that the float arm interferes with or binds to other components in the fuel tank.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace malfunctioning part.
3.
CHECK FUEL LEVEL SENSOR SIGNAL CIRCUIT
Check the fuel level sensor signal circuit. Refer to
MWI-54, "Component Function Check"
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-45, "Intermittent Incident"
.
NO
>> Repair or replace malfunctioning parts.
MWI-60
< SYMPTOM DIAGNOSIS >
THE OIL PRESSURE WARNING LAMP DOES NOT TURN ON
THE OIL PRESSURE WARNING LAMP DOES NOT TURN ON
Description
INFOID:0000000012201343
The oil pressure warning lamp stays off when the ignition switch is turned ON.
Diagnosis Procedure
INFOID:0000000012201344
1.
CHECK COMBINATION METER INPUT SIGNAL
1. Start the engine.
2. Select “Data Monitor” in “METER/M&A” to check that the oil pressure warning lamp state is consistent
with the “OIL W/L” monitor value.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace combination meter. Refer to
MWI
THE OIL PRESSURE WARNING LAMP DOES NOT TURN OFF
MWI-61
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
THE OIL PRESSURE WARNING LAMP DOES NOT TURN OFF
Description
INFOID:0000000012201345
The oil pressure warning lamp remains illuminated while the engine is running (normal oil pressure).
Diagnosis Procedure
INFOID:0000000012201346
1.
CHECK COMBINATION METER INPUT SIGNAL
1. Start the engine.
2. Select “Data Monitor” in “METER/M&A” to check that the oil pressure warning lamp state is consistent
with the “OIL W/L” monitor value.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace combination meter. Refer to
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст