Nissan Juke F15. Instruction — part 1348
TM-582
< UNIT DISASSEMBLY AND ASSEMBLY >
[CVT: RE0F10D]
TORQUE CONVERTER AND CONVERTER HOUSING OIL SEAL
• Drive converter housing oil seal (1) evenly using a drift (A) (com-
mercial service tool) so that converter housing oil seal protrudes by
the dimension (B) respectively.
Unit: mm (in)
NOTE:
Converter housing oil seal pulling direction is used as the refer-
ence.
• Attach the pawl (A) of the torque converter to the drive sprocket
hole (B) on the transaxle assembly side.
CAUTION:
• Rotate the torque converter for installing torque converter.
• Never damage the bushing inside the torque converter
sleeve when installing the converter housing oil seal.
Inspection
INFOID:0000000012201285
INSPECTION AFTER INSTALLATION
Commercial service tool: (A)
Outer diameter: 65 (2.56)
Inner diameter: 60 (2.36)
: Transaxle assembly
SCIA7908J
Dimension (B)
: 1.0
± 0.5 mm (0.039 ± 0.020 in)
SCIA7909J
SCIA7907J
TORQUE CONVERTER AND CONVERTER HOUSING OIL SEAL
TM-583
< UNIT DISASSEMBLY AND ASSEMBLY >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
• After inserting a torque converter to the CVT, check dimension (A)
with in the reference value limit.
B
: Scale
C
: Straightedge
Dimension (A)
: Refer to
.
JPDIA0115ZZ
TM-584
< SERVICE DATA AND SPECIFICATIONS (SDS)
[CVT: RE0F10D]
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
General Specification
INFOID:0000000012201286
Shift Characteristics
INFOID:0000000012201287
Unit: rpm
NOTE:
Lock-up is engaged at the vehicle speed of approximately 18 km/h (11 MPH) to 130 km/h (81 MPH).
Stall Speed
INFOID:0000000012201288
Unit: rpm
Torque Converter
INFOID:0000000012201289
Unit: mm (in)
Applied model
Engine
MR16DDT
Axle
2WD/AWD
Transaxle model
RE0F10D
Transaxle gear ratio
D position
2.631 – 0.378
R position
1.960
Final drive
5.694
Recommended fluid and fluid capacity
MA-11, "Fluids and Lubricants"
Throttle position
Shift pattern
CVT input speed
At 40 km/h (25 MPH)
At 60 km/h (37 MPH)
2/8
“D” position
1,500 – 3,200
1,600 – 3,500
ECO mode
1,500 – 3,200
1,600 – 3,500
8/8
“D” position
4,000 – 4,800
4,600 – 5,400
ECO mode
4,000 – 4,800
4,600 – 5,400
Stall speed
2,600 – 3,040
Dimension “A” between the converter housing and torque converter
14.4 (0.567)
VTL-1
VENTILATION, HEATER & AIR CONDITIONER
C
D
E
F
G
H
J
K
L
M
SECTION
VTL
A
B
VTL
N
O
P
CONTENTS
VENTILATION SYSTEM
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precautions for Removing Battery Terminal . . .....
Precaution for Procedure without Cowl Top Cover
. ..
Precautions For Xenon Headlamp Service . . . ...
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Commercial Service Tool . . . . . . . . . . ..
SYSTEM DESCRIPTION . . . . . . . ..
VENTILATION SYSTEM . . . . . . . . . .
System Description . . . . . . . . . . . . ...
REMOVAL AND INSTALLATION . . . .
DUCT AND GRILLE . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . ..
CENTER VENTILATOR GRILLE . . . . . . . ....
CENTER VENTILATOR GRILLE : Removal and
Installation . . . . . . . . . . . . . . . .....
SIDE DEFROSTER NOZZLE . . . . . . . . . ..
SIDE DEFROSTER NOZZLE : Removal and In-
stallation . . . . . . . . . . . . . . . . ....
SIDE VENTILATOR GRILLE . . . . . . . . . ...
SIDE VENTILATOR GRILLE : Removal and In-
stallation . . . . . . . . . . . . . . . . ....
SIDE DEFROSTER GRILLE . . . . . . . . . .
SIDE DEFROSTER GRILLE : Removal and In-
stallation . . . . . . . . . . . . . . . . ..
FRONT DEFROSTER NOZZLE . . . . . . . .
FRONT DEFROSTER NOZZLE : Removal and In-
stallation . . . . . . . . . . . . . . . . ..
CENTER VENTILATOR DUCT . . . . . . . . ..
CENTER VENTILATOR DUCT : Removal and In-
stallation . . . . . . . . . . . . . . . . ..
SIDE VENTILATOR DUCT . . . . . . . . . .
SIDE VENTILATOR DUCT : Removal and Instal-
lation . . . . . . . . . . . . . . . . . .
REAR HEATER DUCT 1 . . . . . . . . . . .
REAR HEATER DUCT 1 : Removal and Installa-
tion . . . . . . . . . . . . . . . . . . ...
REAR HEATER DUCT 2 . . . . . . . . . . .
REAR HEATER DUCT 2 : Removal and Installa-
tion . . . . . . . . . . . . . . . . . . ...
REAR HEATER DUCT 3 . . . . . . . . . . .
REAR HEATER DUCT 3 : Removal and Installa-
tion . . . . . . . . . . . . . . . . . . ...
FOOT DUCT . . . . . . . . . . . . . . . ...
FOOT DUCT : Removal and Installation . . . . .
BLOWER MOTOR . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
IN-CABIN MICROFILTER . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Replacement . . . . . . . . . . . . . . ...
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст