Nissan Juke F15. Instruction — part 1227
TM-98
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F52H]
TRANSAXLE ASSEMBLY
30. Remove gear components from clutch housing in the following
procedure.
a. Remove a set of input shaft assembly, mainshaft assembly, and
reverse idler gear assembly by tapping the tip of input shaft from
the back of the clutch housing with a plastic hammer.
CAUTION:
Always withdraw mainshaft straight out. Failure to do so
can damage resin oil channel on clutch housing side.
b. Remove final drive assembly.
31. Remove magnet from clutch housing.
32. Remove mainshaft bearing retainer and then mainshaft front
bearing from clutch housing using the Tool.
CAUTION:
Do not damage clutch housing, mainshaft front bearing, or
oil channel.
33. Remove oil channel from clutch housing.
34. Remove differential side bearing outer race (clutch housing
side) from clutch housing using the puller.
CAUTION:
Do not damage clutch housing or differential side bearing
outer race.
35. Remove input shaft oil seal from clutch housing, using a suitable
tool.
CAUTION:
Do not damage clutch housing.
SCIA0964E
PCIB1859E
Tool number
: KV381054S0 (J-34286)
PCIB0937E
Tool number
: KV381054S0 (J-34286)
PCIB0938E
SCIA0398E
TRANSAXLE ASSEMBLY
TM-99
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F52H]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
36. Remove differential side oil seal from clutch housing, using a
suitable tool.
CAUTION:
Do not damage clutch housing.
Assembly
INFOID:0000000012200822
ASSEMBLY
1. Install differential side oil seal (1) to clutch housing using Tool
(A).
CAUTION:
• Do not reuse differential side oil seal.
• When installing, do not incline differential side oil seal.
• Do not damage clutch housing.
PCIB1874E
Dimension (H)
: -0.5 - 0.5 mm (-0.020 - 0.020 in)
Tool number
: ST33400001 (J-26082)
PCIB1864E
TM-100
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F52H]
TRANSAXLE ASSEMBLY
2. Install input shaft oil seal (1) to clutch housing using Tool (A).
CAUTION:
• Do not reuse input shaft oil seal.
• When installing, do not incline input shaft oil seal.
• Do not damage clutch housing.
3. Install differential side bearing outer race (clutch housing side) to
clutch housing using Tools.
CAUTION:
Replace differential side bearing and differential side bear-
ing outer race as a set.
4. Install oil channel (1) on mainshaft side.
CAUTION:
When installing oil channel, fit the rib (A) of oil channel into
the processed area of the spot facing (B).
5. Install mainshaft front bearing to clutch housing using Tool.
CAUTION:
Be careful with the orientation of mainshaft front bearing.
Dimension (H)
: 1.1 - 2.0 mm (0.043 - 0.078 in)
Tool number
: ST35321000 ( — )
PCIB1814E
Tool number
: KV40105320 ( — )
: ST30720000 (J-25405)
PCIB0933E
PCIB1921E
Tool number
: ST33200000 (J-26082)
PCIB0939E
TRANSAXLE ASSEMBLY
TM-101
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F52H]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
6. Install mainshaft bearing retainer (1) to clutch housing and
tighten bolt to the specified torque.
CAUTION:
Install with punched surface facing up.
7. Install magnet to clutch housing.
8. Install final drive assembly into clutch housing.
9. Install input shaft assembly, mainshaft assembly, and reverse
idler gear assembly into clutch housing.
CAUTION:
• Wrap a tape, etc. to the spline of input shaft so as not to
damage the input shaft oil seal.
• Be careful with the orientation of reverse idler shaft.
10. Install striking rod assembly (1) into clutch housing.
2
: Mainshaft front bearing
3
: Oil channel
PCIB1938E
PCIB1859E
SCIA0888E
SCIA0964E
PCIB1857E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст