Nissan Juke F15. Instruction — part 69
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-31
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
*
1
: It is displayed but does not operate on CVT models.
*
2
: OFF is displayed when brake pedal is depressed while brake switch power supply is OFF.
ACTIVE TEST
UNLK SEN -DR
Indicates [On/Off] condition of driver door UNLOCK status
PUSH SW -IPDM
Indicates [On/Off] condition of push-button ignition switch
IGN RLY1 -F/B
Indicates [On/Off] condition of ignition relay 1
DETE SW -IPDM
Indicates [On/Off] condition of P position
SFT PN -IPDM
Indicates [On/Off] condition of P or N position
SFT P -MET
Indicates [On/Off] condition of P position
SFT N -MET
Indicates [On/Off] condition of N position
ENGINE STATE
Indicates [Stop/Stall/Crank/Run] condition of engine states
S/L LOCK-IPDM
NOTE:
This item is displayed, but cannot be monitored
S/L UNLK-IPDM
NOTE:
This item is displayed, but cannot be monitored
S/L RELAY-REQ
NOTE:
This item is displayed, but cannot be monitored
VEH SPEED 1
Display the vehicle speed signal received from combination meter by numerical value [Km/h]
VEH SPEED 2
Display the vehicle speed signal received from ABS or VDC or TCM by numerical value [Km/h]
DOOR STAT-DR
Indicates [LOCK/READY/UNLK] condition of driver side door status
DOOR STAT-AS
Indicates [LOCK/READY/UNLK] condition of passenger side door status
ID OK FLAG
Indicates [Set/Reset] condition of key ID
PRMT ENG STRT
Indicates [Set/Reset] condition of engine start possibility
PRMT RKE STRT
NOTE:
This item is displayed, but cannot be monitored
TRNK/HAT MNTR
NOTE:
This item is displayed, but cannot be monitored
RKE-LOCK
Indicates [On/Off] condition of LOCK signal from Intelligent Key
RKE-UNLOCK
Indicates [On/Off] condition of UNLOCK signal from Intelligent Key
RKE-TR/BD
NOTE:
This item is displayed, but cannot be monitored
RKE-PANIC
Indicates [On/Off] condition of PANIC button of Intelligent Key
RKE-MODE CHG
Indicates [On/Off] condition of MODE CHANGE signal from Intelligent Key
RKE OPE COUN1
When remote keyless entry receiver receives the signal transmitted while operating on Intelli-
gent Key, the numerical value start changing
RKE OPE COUN2
NOTE:
This item is displayed, but cannot be monitored
Monitor Item
Condition
Test item
Description
OUTSIDE BUZZER
This test is able to check Intelligent Key warning buzzer operation
• On: Operate
• Off: Non-operation
INSIDE BUZZER
This test is able to check warning chime in combination meter operation
• Take Out: Take away warning chime sounds when CONSULT screen is touched
• Key: Key warning chime sounds when CONSULT screen is touched
• Knob: OFF position warning chime sounds when CONSULT screen is touched
• Off: Non-operation
BCS-32
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
COMB SW
COMB SW : CONSULT Function (BCM - COMB SW)
INFOID:0000000012200709
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
INDICATOR
This test is able to check warning lamp operation
• KEY ON: “KEY” Warning lamp illuminates when CONSULT screen is touched
• KEY IND: “KEY” Warning lamp blinks when CONSULT screen is touched
• Off: Non-operation
INT LAMP
This test is able to check interior room lamp operation
• On: Operate
• Off: Non-operation
LCD
This test is able to check meter display information
• BP N: Engine start operation indicator lamp indicate when CONSULT screen is touched
• BP I: Engine start operation indicator lamp indicate when CONSULT screen is touched
• ID NG: This item is displayed, but cannot be monitored
• ROTAT: This item is displayed, but cannot be monitored
• SFT P: Shift P warning lamp indicate when CONSULT screen is touched
• INSRT: This item is displayed, but cannot be monitored
• BATT: Key warning lamp indicator when CONSULT screen is touched
• NO KY: Key warning lamp indicator when CONSULT screen is touched
• OUTKEY: Engine start operation indicator lamp indicate when CONSULT screen is touched
• LK WN: Engine start operation indicator lamp indicate when CONSULT screen is touched
FLASHER
This test is able to check security hazard lamp operation
The hazard lamps are activated after “LH/RH/Off” on CONSULT screen is touched
HORN
This test is able to check horn operation
The horn is activated after “ON” on CONSULT screen is touched
P RANGE
This test is able to check CVT shift selector power supply
• On: Operate
• Off: Non-operation
ENGINE SW ILLUMI
This test is able to check push-ignition switch illumination operation
Push-ignition switch illumination illuminates when “ON” on CONSULT screen is touched
PUSH SWITCH INDICATOR
This test is able to check LOCK indicator in push-ignition switch operation
LOCK indicator in push-ignition switch illuminates when “ON” on CONSULT screen is touched
BATTERY SAVER
This test is able to check interior room lamp operation.
The interior room lamp will be activated after “ON” on CONSULT screen is touched.
TRUNK/BACK DOOR
This test is able to check back door opener actuator open operation.
This actuator opens when “Open” on CONSULT screen is touched.
Test item
Description
Monitor item [UNIT]
Description
FR WIPER HI
[Off/On]
Displays the status of the FR WIPER HI switch in combination switch judged by BCM with the combination
switch reading function.
FR WIPER LOW
[Off/On]
Displays the status of the FR WIPER LOW switch in combination switch judged by BCM with the combination
switch reading function.
FR WASHER SW
[Off/On]
Displays the status of the FR WASHER switch in combination switch judged by BCM with the combination
switch reading function.
FR WIPER INT
[Off/On]
Displays the status of the FR WIPER INT switch in combination switch judged by BCM with the combination
switch reading function.
INT VOLUME
[1 - 7]
Displays the status of wiper volume dial position judged by BCM with the combination switch reading function.
TURN SIGNAL R
[Off/On]
Displays the status of the TURN RH switch in combination switch judged by BCM with the combination switch
reading function.
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-33
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
BCM
BCM : CONSULT Function (BCM - BCM)
INFOID:0000000012200710
WORK SUPPORT
IMMU
IMMU : CONSULT Function (BCM - IMMU)
INFOID:0000000012965018
WORK SUPPORT
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
TURN SIGNAL L
[Off/On]
Displays the status of the TURN LH switch in combination switch judged by BCM with the combination switch
reading function.
TAIL LAMP SW
[Off/On]
Displays the status of the TAIL LAMP switch in combination switch judged by BCM with the combination
switch reading function.
HI BEAM SW
[Off/On]
Displays the status of the HI BEAM switch in combination switch judged by BCM with the combination switch
reading function.
HEAD LAMP SW 1
[Off/On]
Displays the status of the HEADLAMP 1 switch in combination switch judged by BCM with the combination
switch reading function.
HEAD LAMP SW 2
[Off/On]
Displays the status of the HEADLAMP 2 switch in combination switch judged by BCM with the combination
switch reading function.
PASSING SW
[Off/On]
Displays the status of the PASSING switch in combination switch judged by BCM with the combination switch
reading function.
AUTO LIGHT SW
[Off/On]
Displays the status of the AUTO LIGHT switch in combination switch judged by BCM with the combination
switch reading function.
FR FOG SW
[Off/On]
Displays the status of the FR FOG switch in combination switch judged by BCM with the combination switch
reading function.
Monitor item [UNIT]
Description
Item
Description
RESET SETTING VALUE
Return a value set with Work Support of each system to a default value in factory shipment.
Service item
Description
CONFIRM DONGLE ID
It is possible to check that dongle unit is applied to the vehicle.
Monitor item
Content
CONFRM ID ALL
Indicates [YET] at all time.
Switches to [DONE] when a registered Intelligent Key backside is contacted to push-button igni-
tion switch.
CONFIRM ID4
CONFIRM ID3
CONFIRM ID2
CONFIRM ID1
NOT REGISTERED
Indicates [ID OK] when key ID that is registered is received or is not yet received.
Indicates [ID NG] when key ID that is not registered is received.
TP 4
Indicates the number of IDs that are registered.
TP 3
TP 2
TP 1
PUSH SW
Indicates [ON/OFF] condition of push-button ignition switch.
BCS-34
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
ACTIVE TEST
BATTERY SAVER
BATTERY SAVER : CONSULT Function (BCM - BATTERY SAVER)
INFOID:0000000012965032
WORK SUPPORT
*:Factory setting
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
Test item
Description
THEFT IND
This test is able to check security indicator lamp operation.
Security indicator lamp is turned on when “ON” on CONSULT screen is touched.
Service item
Setting item
Setting
ROOM LAMP TIMER SET
MODE 1
30 min.
Sets the interior room lamp battery saver timer operating
time.
NOTE:
The factor setting is 10 minutes. The setting cannot be re-
turned to the factory setting, when the setting is changed
once.
MODE 2
60 min.
MODE 3
15 min.
BATTERY SAVER SET
On
*
With the exterior lamp battery saver function
Off
Without the exterior lamp battery saver function
IGN BATTERY SAVER SET
MODE 1
Without
Sets the ignition battery saver timer operating time.
MODE 2
30 min.
MODE 3*
10 min.
MODE 4
5 min.
MODE 5
60 min.
ACC BATTERY SAVER SET
MODE 1
Without
Sets the accessory battery saver timer operating time.
MODE 2*
30 min.
MODE 3
10 min.
MODE 4
5 min.
MODE 5
60 min.
Monitor item
[Unit]
Description
REQ SW-DR
[On/Off]
Indicated [On/Off] condition of door request switch (driver side)
REQ SW-AS
[On/Off]
Indicated [On/Off] condition of door request switch (passenger side)
REQ SW-RR
[On/Off]
NOTE:
This item is displayed, but cannot be monitored
REQ SW-RL
[On/Off]
NOTE:
This item is displayed, but cannot be monitored
PUSH SW
[On/Off]
Indicates [On/Off] condition of push-button ignition switch
UNLK SEN -DR
[On/Off]
Indicates [On/Off] condition of driver door UNLOCK status
DOOR SW-DR
[On/Off]
Indicated [On/Off] condition of front door switch (driver side)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст