Nissan Juke F15. Instruction — part 1288
TM-342
< REMOVAL AND INSTALLATION >
[CVT: RE0F10B]
DIFFERENTIAL SIDE OIL SEAL
• Protrusion size (A)
CAUTION:
Protrusion must fall within
± 0.5mm (0.020 in) of calcu-
lated size.
• Parallelism at four diagonal points (
)
CAUTION:
The difference among four diagonal points must be within
0.3 mm (0.012 in).
NOTE:
If differential side oil seal is uneven while installing, tilt suitable
tool.
6. Check that the protrusion size and parallelism are adequate.
Differential Side Oil Seal (Converter housing Side)
CAUTION:
• Never reuse differential side oil seal.
• Apply ATF to the differential side oil seal lip and around the oil seal.
Install differential side oil seal evenly using a drift [outer diameter: 60
mm (2.36 in)] so that differential side oil seal protrudes by the dimen-
sion (A) respectfully.
NOTE:
The reference is the installation direction of the differential side oil
seal.
Inspection
INFOID:0000000012201039
INSPECTION AFTER INSTALLATION
Check for CVT fluid leakage and CVT fluid level. Refer to
.
JSDIA4815ZZ
JSDIA4814ZZ
Dimension (A)
: Height difference from case end sur-
face is within 1.0
± 0.5 mm (0.039 ±
0.020 in).
JSDIA6885ZZ
OIL PUMP FITTING BOLT
TM-343
< REMOVAL AND INSTALLATION >
[CVT: RE0F10B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
OIL PUMP FITTING BOLT
Description
INFOID:0000000012201040
Replace the oil pump fitting bolt and the O-ring if oil leakage or exudes from the oil pump fitting bolt.
Exploded View
INFOID:0000000012201041
Removal and Installation
INFOID:0000000012201042
REMOVAL
1. Remove Oil pump fitting bolt (1) from transaxle assembly.
2. Remove O-ring from oil pump fitting bolt.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
• Never reuse O-ring.
• Apply CVT fluid to O-ring.
Inspection
INFOID:0000000012201043
INSPECTION AFTER INSTALLATION
Check for CVT fluid leakage and CVT fluid level. Refer to
.
1.
Oil pump fitting bolt
2.
O-ring
3.
Transaxle assembly
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
: Apply CVT fluid
JPDIA0829GB
JPDIA0077ZZ
TM-344
< REMOVAL AND INSTALLATION >
[CVT: RE0F10B]
WATER HOSE
WATER HOSE
Exploded View
INFOID:0000000012201044
Removal and Installation
INFOID:0000000012201045
REMOVAL
WARNING:
Never remove the radiator cap when the engine is hot. Serious burns could occur from high pressure
coolant escaping from the radiator.
CAUTION:
Perform these steps after the coolant temperature has cooled sufficiently.
1. Remove the battery. Refer to
PG-105, "Removal and Installation"
.
2. Remove the ECM and bracket as a set.
3. Remove the water hose.
4. Remove the heater thermostat.
INSTALLATION
Note the following, and Install in the reverse order of removal.
• Refer to the following when installing water hoses.
1.
Heater thermostat assembly
2.
Hose clamp
3.
Water hose
A. Water outlet
B. CVT oil warmer
C. To thermostat housing
D. To oil cooler
: N·m (kg-m, ft-lb)
JSDIA2776GB
Water hose (1)
Installation side tube (2)
Direction of paint mark
Hose insertion depth “L”
Water hose
Water outlet
Upward
A: 27 mm (1.06 in) [End reach-
es the 2-stage bulge.]
CVT oil warmer
Leftward
B: 27 mm (1.06 in) [End reach-
es the tube bend R position).]
Heater thermostat assembly
CVT oil warmer
Leftward
WATER HOSE
TM-345
< REMOVAL AND INSTALLATION >
[CVT: RE0F10B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
• Refer to the followings when installing hose clamp.
CAUTION:
Hose clamp should not interfere with the bulge of fluid cooler tube.
Inspection
INFOID:0000000012201046
INSPECTION AFTER REMOVAL
Heater Thermostat
• Fully immerse the heater thermostat (1) in a container (A) filled
with water. Continue heating the water while stirring.
• Continue heating the heater thermostat for 5 minutes or more after
bringing the water to a boil.
• Quickly take the heater thermostat out of the hot water, measure
the heater thermostat within 10 seconds.
JSDIA2407ZZ
Water hose (1)
Installation side tube (2)
Hose clamp (3)
Direction of tab
Clamping position
Water hose
Water outlet
Backward
A: 5 – 7 mm (0.20 – 0.28 in) (L)
from hose end
CVT oil warmer
Upward
Heater thermostat assembly
CVT oil warmer
Upward
B: Align with the end of paint
mark (C)
JSDIA2499ZZ
JPBIA0318ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст