Nissan Juke F15. Instruction — part 982
MA-20
< PERIODIC MAINTENANCE >
ENGINE MAINTENANCE (MR FOR NISMO RS MODELS)
• Check radiator cap relief pressure.
- When connecting radiator cap to the radiator cap tester (commer-
cial service tool) (A) and the radiator cap tester adapter (commer-
cial service tool) (B), apply engine coolant to the cap seal surface.
• Replace radiator cap if there is an unusualness related to the above three.
CAUTION:
When installing radiator cap, thoroughly wipe out the radiator filler neck to remove any waxy residue
or foreign material.
RADIATOR
RADIATOR : Inspection
INFOID:0000000012200189
Check radiator for mud or clogging. If necessary, clean radiator as follows.
CAUTION:
• Be careful not to bend or damage radiator fins.
• When radiator is cleaned without removal, remove all surrounding parts such as radiator cooling fan
assembly and horns. Then tape harness and harness connectors to prevent water from entering.
1. Apply water by hose to the back side of the radiator core vertically downward.
2. Apply water again to all radiator core surfaces once per minute.
3. Stop washing if any stains no longer flow out from radiator.
4. Blow air into the back side of radiator core vertically downward.
• Use compressed air lower than 490 kPa (4.9 bar, 5 kg/cm
2
, 71 psi) and keep distance more than 30 cm
(11.81 in).
5. Blow air again into all the radiator core surfaces once per minute until no water sprays out.
FUEL LINES
FUEL LINES : Inspection
INFOID:0000000012200190
Inspect fuel lines, fuel filler cap, and fuel tank for improper attach-
ment, leakage, cracks, damage, loose connections, chafing or dete-
rioration.
If necessary, repair or replace damaged parts.
AIR CLEANER FILTER
AIR CLEANER FILTER : Removal and Installation
INFOID:0000000012200191
REMOVAL
Standard and Limit
: Refer to
PBIC5122J
A
: Engine
B
: Fuel line
C
: Fuel tank
JPBIA0129ZZ
ENGINE MAINTENANCE (MR FOR NISMO RS MODELS)
MA-21
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
1. Remove air duct inlet (upper) (1).
2. Unhook the tabs (A) of both ends of the air cleaner cover.
3. Remove the air cleaner filter (1) and air cleaner body (2) from
the air cleaner case.
4. Remove the air cleaner filter from the air cleaner body.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Fixing clips shall be fixed after inserting air cleaner body protrusion to air cleaner case notch hole.
• Make sure that whether air cleaner body has been firmly installed by shaking it.
AIR CLEANER FILTER : Inspection (Viscous Paper Type)
INFOID:0000000012200192
INSPECTION AFTER REMOVAL
Examine with eyes that there is no stain, clogging, or damage on air cleaner element.
• Remove dusts (such as dead leafs) on air cleaner element surface and inside cleaner case.
• If clogging or damage is observed, replace the air cleaner element.
CAUTION:
Never clean the viscous paper type air cleaner element by blowing as there is a risk of deterioration of
its performance
MAINTENANCE INTERVAL
MA-7, "Introduction of Periodic Maintenance"
ENGINE OIL
ENGINE OIL : Draining
INFOID:0000000012200193
WARNING:
• Be careful not to get burned, as engine oil may be hot.
• Prolonged and repeated contact with used engine oil may cause skin cancer. Try to avoid direct skin
contact with used engine oil. If skin contact is made, wash thoroughly with soap or hand cleaner as
soon as possible.
1. Warm up the engine, and check for engine oil leakage from engine components. Refer to
2. Stop the engine and wait for 10 minutes.
3. Loosen oil filler cap.
4. Remove drain plug and then drain engine oil.
JPBIA4352ZZ
JPBIA4353ZZ
MA-22
< PERIODIC MAINTENANCE >
ENGINE MAINTENANCE (MR FOR NISMO RS MODELS)
ENGINE OIL : Refilling
INFOID:0000000012200194
1. Install drain plug with new drain plug washer. Refer to
CAUTION:
Be sure to clean drain plug and install with new drain plug washer.
2. Refill with new engine oil.
Engine oil specification and viscosity: Refer to
MA-11, "Fluids and Lubricants"
.
CAUTION:
• The refill capacity depends on the engine oil temperature and drain time. Use these specifica-
tions for reference only.
• Always use oil level gauge to determine the proper amount of engine oil in the engine.
3. Warm up engine and check area around drain plug and oil filter for engine oil leakage.
4. Stop engine and wait for 10 minutes.
5. Check the engine oil level. Refer to
.
OIL FILTER
OIL FILTER : Removal and Installation
INFOID:0000000012200195
REMOVAL
1. Remove engine under cover.
2. Using oil filter wrench [SST: KV10115801 (J-38956)] (A), remove
oil filter.
CAUTION:
• Oil filter is provided with relief valve. Use genuine NISSAN
oil filter or equivalent.
• Be careful not to get burned when engine and engine oil
may be hot.
• When removing, prepare a shop cloth to absorb any
engine oil leakage or spillage.
• Completely wipe off any engine oil that adheres to engine
and vehicle.
INSTALLATION
1. Remove foreign materials adhering to the oil filter installation surface.
2. Apply new engine oil to the oil seal contact surface of new oil fil-
ter.
Tightening torque
: Refer to
.
Engine oil capacity
: Refer to
LU-19, "Periodical Maintenance Specification"
: Vehicle front
JPBIA4450ZZ
SMA010
ENGINE MAINTENANCE (MR FOR NISMO RS MODELS)
MA-23
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
3. Screw oil filter instructionly until it touches the installation surface,
then tighten it by 2/3 turn (A). Or tighten to specification.
OIL FILTER : Inspection
INFOID:0000000012200196
INSPECTION AFTER INSTALLATION
1. Check the engine oil level. Refer to
.
2. Start the engine, and check that there is no leakage of engine oil.
3. Stop the engine and wait for 10 minutes.
4. Check the engine oil level, and adjust the level. Refer to
.
SPARK PLUG
SPARK PLUG : Removal and Installation
INFOID:0000000012200197
REMOVAL
1. Remove engine cover. Refer to
.
2. Remove air inlet tube assembly. Refer to
.
3. Remove ignition coil.
4. Remove spark plug with a spark plug wrench (commercial ser-
vice tool).
CAUTION:
Never drop or shock spark plug.
INSTALLATION
Install in the reverse order of removal.
SPARK PLUG : Inspection
INFOID:0000000012200198
INSPECTION AFTER REMOVAL
Use the standard type spark plug for normal condition.
CAUTION:
Oil filter:
: 17.7 N·m (1.8 kg-m, 13 ft-lb)
JPBIA0077ZZ
a
: 14 mm (0.55 in)
JPBIA0030ZZ
Spark plug (Standard type)
: Refer to
.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст