Nissan Juke F15. Instruction — part 266
P183D SIDE G SENSOR
DLN-69
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
P183D SIDE G SENSOR
DTC Logic
INFOID:0000000012199417
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and
wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION
With CONSULT
1. Start the engine and drive at 30 km/h (19 MPH) or more for approximately 1 minute.
2. Stop the vehicle.
3. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P183D” detected?
YES
>> Proceed to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000012199418
1.
PERFORM ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF-DIAGNOSIS
With CONSULT
Perform self-diagnosis for “ABS”.
Is any DTC detected?
YES
>> Perform trouble diagnosis for detected DTC. Refer to
NO
>> GO TO 2.
2.
ERASE SELF-DIAGNOSTIC RESULT
With CONSULT
1. Erase self-diagnostic results for “ALL MODE AWD/4WD”.
2. Start the engine and drive at 30 km/h (19 MPH) or more for approximately 1 minute.
3. Stop the vehicle.
4. Check that ABS warning lamp turns OFF.
Does ABS warning lamp turn OFF?
YES
>> GO TO 3.
NO
>> Refer to
BRC-136, "Component Function Check"
.
3.
CHECK TERMINALS AND HARNESS CONNECTORS
Check AWD control module pin terminals for damage or loose connection with harness connector.
Is inspection result normal?
YES
>> After turning the ignition switch OFF, perform DTC confirmation procedure again. If DTC “P183D”
is detected, Replace AWD control module. Refer to
DLN-91, "Removal and Installation"
NO
>> Repair or replace error-detected parts.
DTC
Display item
Malfunction detected condition
Possible cause
P183D
SIDE G SENSOR
Malfunction is detected in side G sensor
signal that is output from ABS actuator
and electric unit (control unit) through
CAN communication.
• ABS actuator and electric unit (control
unit)
• Yaw rate/side/decel G sensor (Side G
sensor signal)
• AWD control module
• CAN communication line
DLN-70
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
P183E YAW RATE SENSOR
P183E YAW RATE SENSOR
DTC Logic
INFOID:0000000012199419
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and
wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION
With CONSULT
1. Start the engine and drive at 30 km/h (19 MPH) or more for approximately 1 minute.
2. Stop the vehicle.
3. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P183E” detected?
YES
>> Proceed to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000012199420
1.
PERFORM ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF-DIAGNOSIS
With CONSULT
Perform self-diagnosis for “ABS”.
Is any DTC detected?
YES
>> Perform trouble diagnosis for detected DTC. Refer to
NO
>> GO TO 2.
2.
ERASE SELF-DIAGNOSTIC RESULT
With CONSULT
1. Erase self-diagnostic results for “ALL MODE AWD/4WD”.
2. Start the engine and drive at 30 km/h (19 MPH) or more for approximately 1 minute.
3. Stop the vehicle.
4. Check that ABS warning lamp turns OFF.
Does ABS warning lamp turn OFF?
YES
>> GO TO 3.
NO
>> Refer to
BRC-136, "Component Function Check"
3.
CHECK TERMINALS AND HARNESS CONNECTORS
Check AWD control module pin terminals for damage or loose connection with harness connector.
Is inspection result normal?
YES
>> After turning the ignition switch OFF, perform DTC confirmation procedure again. If DTC “P183E”
is detected, Replace AWD control module. Refer to
DLN-91, "Removal and Installation"
NO
>> Repair or replace error-detected parts.
DTC
Display item
Malfunction detected condition
Possible cause
P183E
YAWRATE SENSOR
Malfunction is detected in yaw rate sen-
sor signal that is output from ABS actua-
tor and electric unit (control unit) through
CAN communication.
• ABS actuator and electric unit (control
unit)
• Yaw rate/side/decel G sensor (Yaw
rate signal)
• AWD control module
• CAN communication line
P183F GEAR POSITION SIGNAL
DLN-71
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
P183F GEAR POSITION SIGNAL
DTC Logic
INFOID:0000000012199421
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and
wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION
With CONSULT
1. Start the engine.
CAUTION:
Never drive the vehicle.
2. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P183F” detected?
YES
>> Proceed to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000012199422
1.
PERFORM TCM SELF-DIAGNOSIS
With CONSULT
Perform self-diagnosis for “TRANSMISSION”.
Is any DTC detected?
YES
>> Perform trouble diagnosis for detected DTC. Refer to
(RE0F10B),
(RE0F10D).
NO
>> GO TO 2.
2.
CHECK TERMINALS AND HARNESS CONNECTORS
Check AWD control module pin terminals for damage or loose connection with harness connector.
Is inspection result normal?
YES
>> After turning the ignition switch OFF, perform DTC confirmation procedure again. If DTC “P183F”
is detected, Replace AWD control module. Refer to
DLN-91, "Removal and Installation"
NO
>> Repair or replace error-detected parts.
DTC
Display item
Malfunction detected condition
Possible cause
P183F
GEAR POSI SIGNAL
Malfunction is detected in current gear
position signal that is output from TCM
through CAN communication.
• Sensor related to CVT
• TCM
• AWD control module
• CAN communication line
DLN-72
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
P1840 OUTPUT SPEED SIGNAL
P1840 OUTPUT SPEED SIGNAL
DTC Logic
INFOID:0000000012199423
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and
wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION
With CONSULT
1. Start the engine and drive at 30 km/h (19 MPH) or more for approximately 1 minute.
2. Stop the vehicle.
3. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P1840” detected?
YES
>> Proceed to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000012199424
1.
PERFORM TCM SELF-DIAGNOSIS
With CONSULT
Perform self-diagnosis for “TRANSMISSION”.
Is any DTC detected?
YES
>> Perform trouble diagnosis for detected DTC. Refer to
(RE0F10D).
NO
>> GO TO 2.
2.
CHECK TERMINALS AND HARNESS CONNECTORS
Check AWD control module pin terminals for damage or loose connection with harness connector.
Is inspection result normal?
YES
>> After turning the ignition switch OFF, perform DTC confirmation procedure again. If DTC “P1840”
is detected, Replace AWD control module. Refer to
DLN-91, "Removal and Installation"
NO
>> Repair or replace error-detected parts.
DTC
Display item
Malfunction detected condition
Possible cause
P1840
OUTPUT SPEED SIGNAL
Malfunction is detected in output shaft
revolution signal that is output from TCM
through CAN communication.
• Sensor related to CVT
• TCM
• AWD control module
• CAN communication line
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст