Nissan Juke F15. Instruction — part 396
P0500 VSS
EC-397
< DTC/CIRCUIT DIAGNOSIS >
[MR FOR NISMO RS MODELS]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
P0500 VSS
EXCEPT FOR M/T MODELS
EXCEPT FOR M/T MODELS : Description
INFOID:0000000012197929
ECM receives vehicle speed signals from two different paths via CAN communication line: One is from the
ABS actuator and electric unit (control unit) via the combination unit and the other is from TCM.
EXCEPT FOR M/T MODELS : DTC Logic
INFOID:0000000012197930
DTC DETECTION LOGIC
NOTE:
• If DTC P0500 is displayed with DTC UXXXX, first perform the trouble diagnosis for DTC UXXXX.
• If DTC P0500 is displayed with DTC P0607, first perform the trouble diagnosis for DTC P0607. Refer to
.
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is 10 V or more at idle.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1. Start engine.
2. Shift the selector lever to D range and wait at least for 2 seconds.
3. Drive the vehicle at least 5 seconds at 20 km/h (13 MPH) or more.
CAUTION:
Always drive vehicle at a safe speed.
NOTE:
This procedure may be conducted with the drive wheels lifted in the shop or by driving the vehicle. If a
road test is expected to be easier, it is unnecessary to lift the vehicle.
4. Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Proceed to
EC-397, "EXCEPT FOR M/T MODELS : Diagnosis Procedure"
NO
>> INSPECTION END
EXCEPT FOR M/T MODELS : Diagnosis Procedure
INFOID:0000000012197931
1.
CHECK DTC WITH TCM
Check DTC with TCM. Refer to
DTC No.
Trouble diagnosis name
(Trouble diagnosis content)
DTC detecting condition
Possible cause
P0500
VEH SPEED SEN/CIRC
(Vehicle speed sensor)
At 20 km/h (13 MPH), ECM detects the fol-
lowing status continuously for 5 seconds or
more: The difference between a vehicle
speed calculated by a output speed sensor
transmitted from TCM to ECM via CAN com-
munication and the vehicle speed indicated
on the combination meter exceeds 15km/h
(10 MPH).
• Harness or connector
(CAN communication line is open or
shorted.)
• Combination meter
• ABS actuator and electric unit (control
unit)
• Wheel sensor
• TCM
• Output speed sensor
EC-398
< DTC/CIRCUIT DIAGNOSIS >
[MR FOR NISMO RS MODELS]
P0500 VSS
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Perform trouble shooting relevant to DTC indicated.
2.
CHECK DTC WITH ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
Check DTC with ABS actuator and electric unit (control unit). Refer to
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Perform trouble shooting relevant to DTC indicated.
3.
CHECK DTC WITH COMBINATION METER
Check DTC with combination meter. Refer to
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Perform trouble shooting relevant to DTC indicated.
4.
CHECK OUTPUT SPEED SENSOR
Check output speed sensor. Refer to
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace or replace error-detected parts.
5.
CHECK WHEEL SENSOR
Check wheel sensor. Refer to
.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-45, "Intermittent Incident"
.
NO
>> Replace or replace error-detected parts.
M/T MODELS
M/T MODELS : Description
INFOID:0000000012197932
The vehicle speed signal is sent to the combination meter from the “ABS actuator and electric unit (control
unit)” via the CAN communication line. The combination meter then sends a signal to the ECM via the CAN
communication line.
M/T MODELS : DTC Logic
INFOID:0000000012197933
DTC DETECTION LOGIC
NOTE:
• If DTC P0500 is displayed with DTC UXXXX, first perform the trouble diagnosis for DTC UXXXX.
• If DTC P0500 is displayed with DTC P0607, first perform the trouble diagnosis for DTC P0607. Refer
DTC CONFIRMATION PROCEDURE
1.
INSPECTION START
Do you have CONSULT?
Do you have CONSULT?
DTC No.
Trouble diagnosis name
(Trouble diagnosis con-
tent)
DTC detecting condition
Possible cause
P0500
VEH SPEED SEN/CIRC
(Vehicle speed sensor)
The vehicle speed signal sent to ECM
is almost 0 km/h (0 MPH) even when
vehicle is being driven.
• Harness or connectors
(CAN communication line is open or shorted)
• Harness or connectors
(Vehicle speed signal circuit is open or shorted)
• Wheel sensor
• Combination meter
• ABS actuator and electric unit (control unit)
P0500 VSS
EC-399
< DTC/CIRCUIT DIAGNOSIS >
[MR FOR NISMO RS MODELS]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
YES
>> GO TO 2.
NO
>> GO TO 5.
2.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
>> GO TO 3.
3.
CHECK VEHICLE SPEED SIGNAL
NOTE:
This procedure may be conducted with the drive wheels lifted in the shop or by driving the vehicle. If a
road test is expected to be easier, it is unnecessary to lift the vehicle.
With CONSULT
1. Start engine.
2. Read “VHCL SPEED SE” in “DATA MONITOR” mode of “ENGINE” using CONSULT. The vehicle speed
on CONSULT should exceed 10 km/h (6 mph) when rotating wheels with suitable gear position.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Proceed to
EC-400, "M/T MODELS : Diagnosis Procedure"
.
4.
PERFORM DTC CONFIRMATION PROCEDURE
1. Select “DATA MONITOR” mode of “ENGINE” using CONSULT.
2. Warm engine up to normal operating temperature.
3. Maintain the following conditions for at least 50 consecutive seconds.
CAUTION:
Always drive vehicle at a safe speed.
4. Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Proceed to
EC-400, "M/T MODELS : Diagnosis Procedure"
.
NO
>> INSPECTION END
5.
PERFORM COMPONENT FUNCTION CHECK
Perform component function check. Refer to
EC-399, "M/T MODELS : Component Function Check"
.
Use component function check to check the overall function of the vehicle speed signal circuit. During this
check, a 1st trip DTC might not be confirmed.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Proceed to
EC-400, "M/T MODELS : Diagnosis Procedure"
.
M/T MODELS : Component Function Check
INFOID:0000000012197934
1.
PERFORM COMPONENT FUNCTION CHECK
With GST
1. Lift up drive wheels.
2. Start engine.
3. Read vehicle speed signal in Service $01 with GST.
ENG SPEED
1,800 - 6,000 rpm
COOLAN TEMP/S
More than 65
°C (149°F)
B/FUEL SCHDL
6.25 - 31.8 msec
Selector lever
Except Neutral position
PW/ST SIGNAL
OFF
EC-400
< DTC/CIRCUIT DIAGNOSIS >
[MR FOR NISMO RS MODELS]
P0500 VSS
The vehicle speed signal on GST should be able to exceed 10 km/h (6 MPH) when rotating wheels with
suitable gear position.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Proceed to
EC-400, "M/T MODELS : Diagnosis Procedure"
.
M/T MODELS : Diagnosis Procedure
INFOID:0000000012197935
1.
CHECK DTC WITH ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
Check DTC with ABS actuator and electric unit (control unit). Refer to
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Perform trouble shooting relevant to DTC indicated.
2.
CHECK DTC WITH COMBINATION METER
Check DTC with combination meter. Refer to
.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Perform trouble shooting relevant to DTC indicated.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст