Nissan Juke F15. Instruction — part 798
FL-22
< REMOVAL AND INSTALLATION >
[MR16DDT ]
FUEL TANK
3. After connecting, pull out quick connector and centralized under
floor piping by hand. Check connections are secure.
2WD : Inspection
INFOID:0000000012197593
INSPECTION AFTER INSTALLATION
Use the following procedure to check for fuel leakage.
1. Turn ignition switch “ON” (with engine stopped), and check connections for leakage by applying fuel pres-
sure to fuel piping.
2. Start engine and rev it up and check there are no fuel leakage at the fuel system tube and hose connec-
tions.
AWD
AWD : Exploded View
INFOID:0000000012197594
A : Pull
JPBIA0140ZZ
1.
Fuel filler cap
2.
Grommet
3.
Fuel filler tube
4.
Cover
5.
Clamp
6.
Fuel filler hose
7.
EVAP hose protector
8.
Fuel tank band (RH)
9.
Protector
JPBIA4873GB
FUEL TANK
FL-23
< REMOVAL AND INSTALLATION >
[MR16DDT ]
C
D
E
F
G
H
I
J
K
L
M
A
FL
N
P
O
AWD : Removal and Installation
INFOID:0000000012197595
REMOVAL
WARNING:
Be sure to read “General Precautions” when working on the fuel system. Refer to
.
CAUTION:
• Because fuel tank forwardly inclines and becomes unstable when installing/removing, fuel should be
drained if found the remaining quantity.
• Situate vehicle on a flat and solid surface.
1. Drain fuel from fuel tank if necessary.
2. Perform the steps 2 to 7 of “REMOVAL” in “ FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL
PUMP ASSEMBLY”. Refer to
FL-11, "AWD : Removal and Installation"
3. Remove center muffler. Refer to
4. Remove propeller shaft. Refer to
.
5. Remove protector from fuel tank.
6. Remove fuel filler hose (3) at fuel tank side.
7. Disconnect vent hose connector (1).
8. Disconnect vent tube and EVAP hose at rear side of fuel tank.
• Instruction for quick connector (A) of EVAP tube and vent
FL-11, "AWD : Removal and Installation"
9. Remove parking brake cable mounting bolts, and keep a service area. Refer to
.
10. Remove ABS harness connector from fuel tank mounting band.
11. Support left of fuel tank (1) with transmission jack (A), and them
remove fuel tank band (RH) (2).
10. Fuel tank band (LH)
11.
Fuel tank
12. Vent tube
A.
To EVAP canister
Vehicle front
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
1 : Vent tube
2 : EVAP hose
: Vehicle front
JPBIA4474ZZ
JPBIA4475ZZ
FL-24
< REMOVAL AND INSTALLATION >
[MR16DDT ]
FUEL TANK
12. Support right of fuel tank (1) with transmission jack (A), and then
remove fuel tank band mounting bolts (LH).
13. Supporting with hands, descend transmission jack carefully, and remove fuel tank with fuel tank band
(LH).
CAUTION:
Fuel tank may be in an unstable condition because of the shape of fuel tank bottom. Never rely on
jack too much. Be sure to hold tank securely.
INSTALLATION
Note the following, and install in the reverse order of removal.
Fuel Filler Hose
• Insert fuel filler hose to the length below.
• Be sure hose clamp is not placed on swelled area of fuel filler tube.
• Tighten the clamp band with the top mark (A) until the mark is on
the bolt head flange.
EVAP Hose
1. Check connections for damage or foreign material.
2. Align the matching side connection part with the center of shaft,
and insert connector straight until it clicks.
3. After connecting, pull out quick connector and centralized under-
floor piping by hand. Make sure connections are secure.
AWD : Inspection
INFOID:0000000012197596
INSPECTION AFTER INSTALLATION
Use the following procedure to check for fuel leakage.
1. Turn ignition switch “ON” (with engine stopped), and check connections for leakage by applying fuel pres-
sure to fuel piping.
JPBIA4476ZZ
: 35 mm (1.38 in)
JPBIA0146ZZ
A
: Pull
JPBIA0140ZZ
FUEL TANK
FL-25
< REMOVAL AND INSTALLATION >
[MR16DDT ]
C
D
E
F
G
H
I
J
K
L
M
A
FL
N
P
O
2. Start engine and rev it up and check there are no fuel leakage at the fuel system tube and hose connec-
tions.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст