Nissan Juke F15. Instruction — part 467
ECM
EC-681
< ECU DIAGNOSIS INFORMATION >
[MR EXCEPT FOR NISMO RS MODELS]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
EXH/V TIM B1
• Engine: After warming up
• Selector lever: P or N (CVT),
Neutral (M/T)
• Air conditioner switch: OFF
• No load
Idle
−5° - 5°CA
Around 2,500 rpm while the engine speed
is rising
Approx. 0
° - 30°CA
INT/V SOL(B1)
• Engine: After warming up
• Selector lever: P or N (CVT),
Neutral (M/T)
• Air conditioner switch: OFF
• No load
Idle
Approx. 46%
2,000 rpm
Approx. 46%
AIR COND RLY
Engine: After warming up, idle the
engine
Air conditioner switch: OFF
OFF
Air conditioner switch: ON
(Compressor operates)
ON
FUEL PUMP RLY
• For 1 seconds after turning ignition switch: ON
• Engine running or cranking
ON
Except above
OFF
THRTL RELAY
Ignition switch: ON
ON
HO2S2 HTR (B1)
• Engine speed: Below 3,600 rpm after the following conditions are met.
- Engine: After warming up
- Keeping the engine speed between 3,500 and 4,000 rpm for 1 minute and at
idle for 1 minute under no load
ON
Engine speed: Above 3,600 rpm
OFF
W/GATE V CLSD
LEARN B1
Ignition switch: ON
Waste gate valve closed learning has not
been performed yet.
INCMP
Waste gate valve closed learning has al-
ready been performed successfully.
CMPLT
W/G ACTUATOR
POSITION B1
Ignition switch: ON
Approx. 0.008 m
Engine: After warming up
Idle
Approx. 0.008 m
2,000 rpm
Approx. 0.008 m
4,000 rpm
Approx. 0.008 m
W/G ACTUATOR
POSI SEN B1
Ignition switch: ON
Approx. 4.0 V
Engine: After warming up
Idle
Approx. 4.0 V
2,000 rpm
Approx. 4.0 V
4,000 rpm
Approx. 4.0 V
EGR VALVE POSI-
TION
Ignition switch: ON
Approx. 1 deg
Engine: After warming up
Idle
Approx. 0 deg
2,000 rpm
Approx. 0 deg
4,000 rpm
Approx. 0 deg
EGR VALVE POSI-
TION SEN
Ignition switch: ON
Approx. 1.26 V
Engine: After warming up
Idle
Approx. 1.20 V
2,000 rpm
Approx. 1.26 V
4,000 rpm
Approx. 1.26 V
EGR DIFFEREN-
TIAL PRESS
Engine: After warming up
Idle
Approx. 1 kPa
2,000 rpm
Approx. 1 kPa
4,000 rpm
Approx. 3 kPa
ALT DUTY SIG
Power generation voltage variable control: Operating
ON
Power generation voltage variable control: Not operating
OFF
I/P PULLY SPD
Vehicle speed: More than 20 km/h (12 MPH)
Almost the same speed as
the tachometer indication
Monitor Item
Condition
Values/Status
EC-682
< ECU DIAGNOSIS INFORMATION >
[MR EXCEPT FOR NISMO RS MODELS]
ECM
VEHICLE SPEED
Turn drive wheels and compare CONSULT value with the speedometer indica-
tion.
Almost the same speed as
the speedometer indication
IDL A/V LEARN
Engine: running
Idle air volume learning has not been per-
formed yet.
YET
Idle air volume learning has already been
performed successfully.
CMPLT
TRVL AFTER MIL
Ignition switch: ON
Vehicle has traveled after MIL has illumi-
nated.
0 - 65,535 km (0 - 40,723
miles)
ENG OIL TEMP
Engine: After warming up
More than 70
°C (158°F)
A/F S1 HTR(B1)
Engine: After warming up, idle the engine
(More than 260 seconds after starting engine)
4 - 100%
INT/A TEMP SE
Ignition switch: ON
Indicates intake air tempera-
ture
SET VHCL SPD
Engine: Running
ASCD: Operating
The preset vehicle speed is
displayed
MAIN SW
Ignition switch: ON
MAIN switch: Pressed
ON
MAIN switch: Released
OFF
CANCEL SW
Ignition switch: ON
CANCEL switch: Pressed
ON
CANCEL switch: Released
OFF
RESUME/ACC SW
Ignition switch: ON
ACCEL/RES switch: Pressed
ON
ACCEL/RES switch: Released
OFF
SET SW
Ignition switch: ON
COAST/SET switch: Pressed
ON
COAST/SET switch: Released
OFF
BRAKE SW1
(Brake pedal posi-
tion switch)
Ignition switch: ON
Brake pedal: Fully released
ON
Brake pedal: Slightly depressed
OFF
BRAKE SW2
(Stop lamp switch)
Ignition switch: ON
Brake pedal: Fully released
OFF
Brake pedal: Slightly depressed
ON
VHCL SPD CUT
Ignition switch: ON
NON
LO SPEED CUT
Ignition switch: ON
NON
AT OD MONITOR
Ignition switch: ON
OFF
AT OD CANCEL
Ignition switch: ON
OFF
CRUISE LAMP
Ignition switch: ON
MAIN switch: Pressed at the 1st time
→
at the 2nd time
ON
→ OFF
SET LAMP
• MAIN switch: ON
• When vehicle speed is between
40 km/h (25 MPH) and 194
km/h (120 MPH)
ASCD: Operating
ON
ASCD: Not operating
OFF
FAN DUTY
Engine: Running
0 - 100%
ALT DUTY
Engine: Idle
0 - 80%
BAT CUR SEN
• Engine speed: Idle
• Battery: Fully charged
*2
• Selector lever: P or N (CVT), Neutral (M/T)
• Air conditioner switch: OFF
• No load
Approx. 2,600 - 3,500 mV
A/F ADJ-B1
Engine: Running
−0.450 - 0.330
P/N POSI SW
Ignition switch: ON
Selector lever: P or N (CVT), Neutral (M/
T)
ON
Selector lever: Except above
OFF
Monitor Item
Condition
Values/Status
ECM
EC-683
< ECU DIAGNOSIS INFORMATION >
[MR EXCEPT FOR NISMO RS MODELS]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
AC PRESS SEN
• Engine: Idle
• Both A/C switch and blower fan switch: ON (Compressor operates)
1.0 - 4.0 V
FUEL PRES SEN
• Engine: After warming up
• Selector lever: P or N (CVT),
Neutral (M/T)
• Air conditioner switch: OFF
• No load
Idle
Approx. 5.0 MPa
2,000 rpm
Approx. 2.5 MPa
TURBO BST SEN
• Engine speed: Idle
• Selector lever: D (CVT), Neutral
(M/T)
• Fuel: Premium gasoline
• The accelerator pedal is depressed to
a half stroke position or more.
• The readings of boost in the multi-func-
tion meter are the same as the ambient
pressure or more.
• Engine speed: More than 3,000 rpm
3.07 - 3.15 V
• Engine speed: Idle
• Selector lever: D (CVT), Neutral
(M/T)
• Fuel: Regular gasoline
• The accelerator pedal is depressed to
a half stroke position or more.
• The readings of boost in the multi-func-
tion meter are the same as the ambient
pressure or more.
• Engine speed: More than 3,000 rpm
2.91 - 2.99 V
FUEL INJ TIM
• Engine: After warming up
• Selector lever: P or N (CVT),
Neutral (M/T)
• Air conditioner switch: OFF
• No load
Idle
Approx. 108 BTDC
2,000 rpm
Approx.
−68 BTDC
FUEL INJ B1
• Engine: After warming up
• Selector lever: P or N (CVT),
Neutral (M/T)
• Air conditioner switch: OFF
• No load
Idle
Approx. 1.1 msec
2,000 rpm
Approx. 1.2 msec
BAT TEMP SEN
• Engine: After warming up
• Selector lever: P or N (CVT),
Neutral (M/T)
• Air conditioner switch: OFF
• No load
Idle
Approx. 0.68 V
A/F SEN1 DIAG1
(B1)
DTC P015A and P015B self-diagnosis is incomplete.
INCMP
DTC P015A and P015B self-diagnosis is complete.
CMPLT
A/F SEN1 DIAG2
(B1)
DTC P014C and P014D self-diagnosis is incomplete.
INCMP
DTC P014C and P014D self-diagnosis is complete.
CMPLT
A/F SEN1 DIAG3
(B1)
The vehicle condition is not within the diagnosis range of DTC P014C, P014D,
P015A or P015B.
ABSNT
The vehicle condition is within the diagnosis range of DTC P014C, P014D,
P015A or P015B.
PRSNT
HO2 S2 DIAG1(B1)
DTC P0139 self-diagnosis (delayed response) has not been performed yet.
INCMP
DTC P0139 self-diagnosis (delayed response) has already been performed suc-
cessfully.
CMPLT
HO2 S2 DIAG2(B1)
DTC P0139 self-diagnosis (slow response) has not been performed yet.
INCMP
DTC P0139 self-diagnosis (slow response) has already been performed suc-
cessfully.
CMPLT
H/P FUEL PUMP
DEG
• Engine: After warming up
• Selector lever: P or N (CVT),
Neutral (M/T)
• Air conditioner switch: OFF
• No load
Idle
Approx. 241 deg
2,000 rpm
Approx. 245 deg
Monitor Item
Condition
Values/Status
EC-684
< ECU DIAGNOSIS INFORMATION >
[MR EXCEPT FOR NISMO RS MODELS]
ECM
FUEL PRES SEN V
• Engine: After warming up
• Selector lever: P or N (CVT),
Neutral (M/T)
• Air conditioner switch: OFF
• No load
Idle
1,140 - 1,460 mV
Revving engine from idle to 4,000 rpm
quickly
1,3000 - 2,900 mV
EOP SENSOR
• Engine: After warming up
• Selector lever: P or N (CVT),
Neutral (M/T)
• Air conditioner switch: OFF
• No load
Idle
1,250 - 1,400 mV
2,000 rpm
1,400 - 2,200 mV
BOOST S/V DUTY
Engine: After warming up
Idle
0 %
• The accelerator pedal is depressed to
a half stroke position or more.
• Engine speed: Below 3,000 rpm
100 %
• The accelerator pedal is depressed to
a half stroke position or more.
• Engine speed: More than 3,000 rpm
30 - 60 %
ATOM PRES SEN
Ignition switch: ON
3.15 - 4.60 V
A/F-S ATMSPHRC
CRCT B1
Engine: After warming up, idle the engine.
Varies depending on vehicle
environment.
A/F-S ATMSPHRC
CRCT UP B1
Engine: Running
Varies depending on the
number of updates.
ECM TEMP 1
• Engine: After cooling
• Ignition switch: ON
Indicates the temperature
around the ECM.
ECM TEMP 2
• Engine: After cooling
• Ignition switch: ON
Indicates the temperature
around the ECM.
SL TRG VHCL SPD Ignition switch: ON
Speed limiter operating
The preset vehicle speed is
displayed
SL SET LAMP
• Ignition switch: ON
• Speed limiter MAIN switch: ON
Speed limiter: Not operating
OFF
Speed limiter: Operating
ON
SL LIMIT LAMP
Ignition switch: ON
Speed limiter MAIN switch: Pressed at
the 1st time
→ at the 2nd time
ON
→ OFF
SL MAIN SW
Ignition switch: ON
Speed limiter MAIN switch: Pressed
ON
Speed limiter MAIN switch: Released
OFF
KICKDOWN POS
Ignition switch: ON
Accelerator pedal: Fully released
OFF
Accelerator pedal: Fully depressed
ON
THRTL STK CNT B1
NOTE:
The item is indicated, but not used.
—
FUEL T/TMP SE
Ignition switch: ON
Indicates fuel tank tempera-
ture.
FUEL LEVEL SE
Ignition switch: ON
Depending on fuel level of
fuel tank
EVAP LEAK DIAG
Ignition switch: ON
Indicates the condition of
EVAP leak diagnosis.
EVAP DIAG READY
Ignition switch: ON
Indicates the ready condition
of EVAP leak diagnosis.
G SENSOR
Vehicle is level
Approx. 2.5 V
TUMBLE POS SEN
• Ignition switch: ON
• Engine coolant temperature: Be-
tween
−)7°C (19°F) – (+)60°C
(140
°F)
Accelerator pedal: Fully released
Less than 1.4 V
Accelerator pedal: Fully depressed
More than 2.8 V
EVAP SYS PRES
Ignition switch: ON
Approx 0.5 - 4.6 V
Monitor Item
Condition
Values/Status
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст