Nissan Juke F15. Instruction — part 1137
SEC-72
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B2603 SHIFT POSITION
3. Check voltage between transmission range switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> GO TO 4.
4.
CHECK TRANSMISSION RANGE SWITCH POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check continuity between transmission range switch harness connector and IPDM E/R harness connec-
tor.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-37, "Removal and Installation"
NO
>> Repair or replace harness.
5.
CHECK BCM INPUT SIGNAL
1. Turn ignition switch OFF.
2. Connect transmission range switch harness connector.
3. Turn ignition switch ON.
4. Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 13.
NO
>> GO TO 6.
6.
CHECK BCM INPUT SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect transmission range switch connector.
3. Disconnect BCM connector.
4. Check continuity between transmission range switch harness connector and BCM harness connector.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Repair or replace harness.
7.
CHECK TRANSMISSION RANGE SWITCH
SEC-74, "Component Inspection (Transmission Range Switch)"
.
Is the inspection result normal?
(+)
(–)
Voltage (V)
Transmission range switch
Connector
Terminal
F27
1
Ground
6 - 16
Transmission range switch
IPDM E/R
Continuity
Connector
Terminal
Connector
Terminal
F27
1
E15
58
Existed
(+)
(–)
Condition
Voltage (V)
(Approx.)
BCM
Connector
Terminal
M70
102
Ground
Selector lever
P or N position
Battery voltage
Other than above
0
Transmission range switch
BCM
Continuity
Connector
Terminal
Connector
Terminal
F27
2
M70
102
Existed
B2603 SHIFT POSITION
SEC-73
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
YES
>> GO TO 12.
NO
>> Replace transmission range switch. Refer to
TM-326, "Removal and Installation"
.
8.
CHECK CVT SHIFT SELECTOR POWER SUPPLY
1. Turn ignition switch OFF.
2. Disconnect CVT shift selector (detention switch) connector.
3. Check voltage between CVT shift selector (detention switch) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 10.
NO
>> GO TO 9.
9.
CHECK CVT SHIFT SELECTOR POWER SUPPLY CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between CVT shift selector (detention switch) harness connector and BCM harness con-
nector.
3. Check continuity between CVT shift selector (detention switch) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 12.
NO
>> Repair or replace harness.
10.
CHECK CVT SHIFT SELECTOR CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between CVT shift selector (detention switch) harness connector and BCM harness con-
nector.
3. Check continuity between CVT shift selector (detention switch) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 11.
NO
>> Repair or replace harness.
11.
CHECK CVT SHIFT SELECTOR (DETENTION SWITCH)
SEC-74, "Component Inspection [CVT Shift Selector (Detention Switch)]"
.
Is the inspection result normal?
(+)
(–)
Voltage (V)
(Approx.)
CVT shift selector (detention switch)
Connector
Terminal
M57
12
Ground
12
CVT shift selector (detention switch)
BCM
Continuity
Connector
Terminal
Connector
Terminal
M57
12
M70
104
Existed
CVT shift selector (detention switch)
Ground
Continuity
Connector
Terminal
M57
12
Not existed
CVT shift selector (detention switch)
BCM
Continuity
Connector
Terminal
Connector
Terminal
M57
13
M68
37
Existed
CVT shift selector (detention switch)
Ground
Continuity
Connector
Terminal
M57
13
Not existed
SEC-74
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B2603 SHIFT POSITION
YES
>> GO TO 13.
NO
>> Replace CVT shift selector. Refer to
TM-316, "Removal and Installation"
12.
CHECK INTERMITTENT INCIDENT
GI-45, "Intermittent Incident"
>> INSPECTION END
13.
REPLACE BCM
1. Replace BCM. Refer to
BCS-94, "Removal and Installation"
.
2. Perform initialization of BCM and registration of all Intelligent Keys using CONSULT.
>> INSPECTION END
Component Inspection (Transmission Range Switch)
INFOID:0000000012202165
1.
CHECK TRANSMISSION RANGE SWITCH
1. Turn ignition switch OFF.
2. Disconnect transmission range switch connector.
3. Check continuity between transmission range switch terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace transmission range switch. Refer to
TM-326, "Removal and Installation"
.
Component Inspection [CVT Shift Selector (Detention Switch)]
INFOID:0000000012202166
1.
CHECK CVT SHIFT SELECTOR (DETENTION SWITCH)
1. Turn ignition switch OFF.
2. Disconnect CVT shift selector connector.
3. Check continuity between CVT shift selector (detention switch) terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace CVT shift selector. Refer to
TM-316, "Removal and Installation"
Transmission range switch
Condition
Continuity
Terminal
1
2
P or N position
Existed
Other than above
Not existed
CVT shift selector (detention switch)
Condition
Continuity
Terminal
12
13
Selector lever: P position
Selector button: Released
Not existed
Selector button: Pressed
Existed
Selector lever: Except P position
B2604 SHIFT POSITION
SEC-75
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B2604 SHIFT POSITION
DTC Logic
INFOID:0000000012202167
DTC DETECTION LOGIC
NOTE:
• If DTC B2604 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
• If DTC B2604 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Shift the selector lever to the P position.
2. Turn ignition switch ON and wait 5 seconds or more.
3. Shift the selector lever to the N position and wait 5 seconds or more.
4. Shift the selector lever to any position other than P and N, and wait 5 seconds or more.
5. Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000012202168
1.
CHECK DTC OF TCM
Check DTC in “Self Diagnostic Result” mode of “TCM” using CONSULT.
Is DTC detected?
YES
>> Perform the trouble diagnosis related to the detected DTC. Refer to
NO
>> GO TO 2.
2.
CHECK BCM INPUT SIGNAL
1. Turn ignition switch ON.
2. Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 4.
3.
REPLACE BCM
1. Replace BCM. Refer to
BCS-94, "Removal and Installation"
.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B2604
PNP/CLUTCH SW
The following states are detected for 5 seconds
while ignition switch is ON.
• P/N position signal is sent from transmission
range switch but shift position signal input
(CAN) from TCM is other than P and N
• P/N position signal is not sent from transmis-
sion range switch but shift position signal input
(CAN) from TCM is P or N
• Harness or connectors
(CAN communication line is open
or shorted.)
• Harness or connectors
(Transmission range switch circuit
is open or shorted.)
• Transmission range switch
• TCM
• BCM
(+)
(–)
Condition
Voltage (V)
(Approx.)
BCM
Connector
Terminal
M70
102
Ground
Selector lever
P or N position
Battery voltage
Other than above
0
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст