Nissan Juke F15. Instruction — part 339
HOW TO SET SRT CODE
EC-169
< BASIC INSPECTION >
[MR FOR NISMO RS MODELS]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
If a vehicle has failed the state emissions inspection due to one or more SRT items indicating “INCMP”, review
the flowchart diagnostic sequence, referring to the following flowchart.
SRT Set Driving Pattern
INFOID:0000000012197732
CAUTION:
JSBIA0400GB
EC-170
< BASIC INSPECTION >
[MR FOR NISMO RS MODELS]
HOW TO SET SRT CODE
Always drive the vehicle in safe manner according to traffic conditions and obey all traffic laws.
*1: Depress the accelerator pedal until vehicle speed is 90 km/h (56 MPH), then release the accelerator pedal
and keep it released for more than 10 seconds. Depress the accelerator pedal until vehicle speed is 90 km/h
(56 MPH) again.
*2: Checking the vehicle speed with GST is advised.
• The time required for each diagnosis varies with road surface conditions, weather, altitude, individual driving
habits, etc.
• “Zone A” is the fastest time where required for the diagnosis under normal conditions*. If the diagnosis is not
completed within “Zone A”, the diagnosis can still be performed within “Zone B”.
JPBIA5321GB
HOW TO SET SRT CODE
EC-171
< BASIC INSPECTION >
[MR FOR NISMO RS MODELS]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
*: Normal conditions
- Sea level
- Flat road
- Ambient air temperature: 20 – 30
°C (68 – 86°F)
NOTE:
Diagnosis is performed as quickly as possible under normal conditions. However, under other conditions,
diagnosis may also be performed. [For example: ambient air temperature other than 20 – 30
°C (68 – 86°F)]
Work Procedure
INFOID:0000000012197733
1.
CHECK DTC
Check DTC.
Is any DTC detected?
YES
>> Repair malfunction(s) and erase DTC. Refer to
.
NO
>> GO TO 2.
2.
CHECK SRT STATUS
With CONSULT
Select “SRT STATUS” in “DTC & SRT CONFIRMATION” mode with CONSULT.
Without CONSULT
Perform “SRT status” mode with
EC-81, "On Board Diagnosis Function"
With GST
Select Service $01 with GST.
Is SRT code(s) set?
YES
>> GO TO 11.
NO-1 >> With CONSULT: GO TO 3.
NO-2 >> Without CONSULT: GO TO 4.
3.
DTC CONFIRMATION PROCEDURE
1. Select “SRT WORK SUPPORT” in “DTC & SRT CONFIRMATION” mode with CONSULT.
2. For SRT(s) that is not set, perform the corresponding “DTC CONFIRMATION PROCEDURE” according to
the “Performance Priority” in the “SRT ITEM” table. Refer to
.
3. Check DTC.
Is any DTC detected?
YES
>> Repair malfunction(s) and erase DTC. Refer to
.
NO
>> GO TO 10.
4.
PERFORM ROAD TEST
• Check the “Performance Priority” in the “SRT ITEM” table. Refer to
• Perform the most efficient SRT set driving pattern to set the SRT properly. Refer to
.
In order to set all SRTs, the SRT set driving pattern must be performed at least once.
>> GO TO 5.
5.
PATTERN 1
1. Check the vehicle condition;
-
Engine coolant temperature is
−10 to 35°C (14 to 95°F).
-
Fuel tank temperature is more than 0
°C (32°F).
2. Start the engine.
3. Keep engine idling until the engine coolant temperature is greater than 70
°C (158°F)
NOTE:
ECM terminal voltage is follows;
• Engine coolant temperature
-
−10 to 35°C (14 to 95°F): 3.0 – 4.3 V
- 70
°(158°F): Less than 4.1 V
• Fuel tank temperature: Less than 1.4 V
.
EC-172
< BASIC INSPECTION >
[MR FOR NISMO RS MODELS]
HOW TO SET SRT CODE
>> GO TO 6.
6.
PATTERN 2
1. Drive the vehicle. And depress the accelerator pedal until vehicle speed is 90 km/h (56 MPH), then
release the accelerator pedal and keep it released for more than 10 seconds.
2. Depress the accelerator pedal until vehicle speed is 90 km/h (56 MPH) again
NOTE:
• Checking the vehicle speed with GST is advised.
• When steady-state driving is performed again even after it is interrupted, each diagnosis can be conducted.
In this case, the time required for diagnosis may be extended.
>> GO TO 7.
7.
PATTERN 3
• Operate vehicle following the driving pattern shown in the figure.
- Release the accelerator pedal during deceleration of vehicle speed
from 90 km/h (56 MPH) to 0 km/h (0 MPH).
>> GO TO 8.
8.
PATTERN 4
• Operate vehicle following the driving pattern shown in the figure.
- Drive the vehicle in a proper gear at 60 km/h (38 MPH) and main-
tain the speed.
- Release the accelerator pedal fully at least 5 seconds.
- Repeat the above two steps at least 5 times.
>> GO TO 9.
9.
PATTERN 5
• The accelerator pedal must be held very steady during steady-state driving.
• If the accelerator pedal is moved, the test must be conducted again.
>> GO TO 10.
10.
CHECK SRT STATUS
With CONSULT
Select “SRT STATUS” in “DTC & SRT CONFIRMATION” mode with CONSULT.
Without CONSULT
Perform “SRT status” mode with
EC-81, "On Board Diagnosis Function"
With GST
Select Service $01 with GST.
Is SRT(s) set?
YES
>> GO TO 11.
NO
>> Call TECH LINE or take appropriate action.
11.
CHECK PERMANENT DTC
PBIB2244E
JSBIA0160GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст