Nissan Juke F15. Instruction — part 1032
PCS-72
< DTC/CIRCUIT DIAGNOSIS >
[POWER DISTRIBUTION SYSTEM]
B261A PUSH-BUTTON IGNITION SWITCH
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-94, "Removal and Installation"
NO
>> Repair or replace harness.
3.
CHECK IGNITION SWITCH OUTPUT SIGNAL (IPDM E/R)
Check voltage between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> Replace IPDM E/R.
NO
>> GO TO 4.
4.
CHECK PUSH-BUTTON IGNITION SWITCH CIRCUIT (IPDM E/R)
1. Disconnect BCM connector.
2. Check continuity between IPDM E/R harness connector and push-button ignition switch harness connec-
tor.
3. Check continuity between push-button ignition switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace harness.
5.
CHECK INTERMITTENT INCIDENT
GI-45, "Intermittent Incident"
>> INSPECTION END
Push-button ignition switch
Ground
Continuity
Connector
Terminal
M101
8
Not existed
(+)
(–)
Voltage (V)
(Approx.)
IPDM E/R
Connector
Terminal
E17
66
Ground
12
IPDM E/R
Push-button ignition switch
Continuity
Connector
Terminal
Connector
Terminal
E17
66
M101
8
Existed
Push-button ignition switch
Ground
Continuity
Connector
Terminal
M101
8
Not existed
PCS
B26F1 IGNITION RELAY
PCS-73
< DTC/CIRCUIT DIAGNOSIS >
[POWER DISTRIBUTION SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
B26F1 IGNITION RELAY
DTC Logic
INFOID:0000000012197210
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON under the following conditions, and wait for 2 seconds or more.
CVT models
-
Selector lever is in the P or N position
-
Do not depress brake pedal
M/T models
-
Do not depress clutch pedal
2. Check “Self-diagnosis result” with CONSULT.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000012197211
1.
CHECK IPDM E/R SELF-DIAGNOSTIC RESULT
1. Turn ignition switch ON.
2. Erase the DTC of IPDM E/R.
3. Turn ignition switch OFF.
4. Turn ignition switch ON and check the DTC again.
Is DTC detected?
YES
>> Repair or replace the malfunctioning part. Refer to
NO
>> GO TO 2.
2.
CHECK IGNITION RELAY (IPDM E/R) CONTROL SIGNAL
Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace BCM. Refer to
BCS-94, "Removal and Installation"
3.
CHECK IGNITION RELAY (IPDM E/R) CONTROL SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM and IPDM connectors.
3. Check continuity between BCM harness connector and IPDM E/R harness connector.
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
B26F1
IGN RELAY OFF
BCM transmits the ignition relay control signal
(ON: 0 V) or ignition switch ON signal (ON)
(CAN), but does not receives ignition switch
ON signal (ON) (CAN) from IPDM E/R.
• Harness or connectors
(Ignition relay circuit is open)
• BCM
• IPDM E/R
(+)
(–)
Condition
Voltage (V)
(Approx.)
BCM
Connector
Terminal
M70
98
Ground
Ignition switch
ON
0
PCS-74
< DTC/CIRCUIT DIAGNOSIS >
[POWER DISTRIBUTION SYSTEM]
B26F1 IGNITION RELAY
Is the inspection result normal?
YES
>> Replace IPDM E/R.
NO
>> Repair or replace harness.
BCM
IPDM E/R
Continuity
Connector
Terminal
Connector
Terminal
M70
98
E17
68
Existed
PCS
B26F2 IGNITION RELAY
PCS-75
< DTC/CIRCUIT DIAGNOSIS >
[POWER DISTRIBUTION SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
B26F2 IGNITION RELAY
DTC Logic
INFOID:0000000012197212
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON under the following conditions, and wait for 2 seconds or more.
CVT models
-
Selector lever is in the P or N position
-
Do not depress brake pedal
M/T models
-
Do not depress clutch pedal
2. Check “Self-diagnosis result” with CONSULT.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000012197213
1.
CHECK IPDM E/R SELF-DIAGNOSTIC RESULT
1. Turn ignition switch ON.
2. Erase the DTC of IPDM E/R.
3. Turn ignition switch OFF.
4. Turn ignition switch ON and check the DTC again.
Is DTC detected?
YES
>> Repair or replace the malfunctioning part. Refer to
NO
>> GO TO 2.
2.
CHECK IGNITION RELAY (IPDM E/R) CONTROL SIGNAL
1. Turn ignition switch OFF.
2. Check voltage between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> Replace IPDM E/R.
NO
>> GO TO 3.
3.
CHECK IGNITION RELAY (IPDM E/R) CONTROL SIGNAL CIRCUIT - 1
1. Turn ignition switch OFF.
2. Disconnect BCM and IPDM E/R connectors.
3. Check continuity between IPDM E/R harness connector and ground.
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
B26F2
IGN RELAY ON
BCM transmits the ignition relay control signal
(OFF: 12 V) or ignition switch ON signal (OFF)
(CAN), but does not receives ignition switch
ON signal (OFF) (CAN) from IPDM E/R.
• Harness or connectors
(Ignition relay circuit is short)
• BCM
• IPDM E/R
(+)
(–)
Condition
Voltage (V)
(Approx.)
IPDM E/R
Connector
Terminal
E17
68
Ground
Ignition switch
OFF or ACC
12
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст