Nissan Juke F15. Instruction — part 812
ABBREVIATIONS
GI-17
< HOW TO USE THIS MANUAL >
C
D
E
F
G
H
I
J
K
L
M
B
GI
N
O
P
P
R
S
T
U
OC
Oxidation catalytic converter
OD
Overdrive
OL
Open loop
OSS
Output shaft speed
ABBREVIATION
DESCRIPTION
P/S
Power steering
PBR
Potentio balance resistor
PCV
Positive crankcase ventilation
PFCW
Predictive forward collision warning
PNP
Park/Neutral position
PSP
Power steering pressure
PTC
Positive temperature coefficient
PTO
Power takeoff
PWM
Pulse width modulation
ABBREVIATION
DESCRIPTION
RAM
Random access memory
RAS
Rear active steer
RH
Right-hand
ROM
Read only memory
RPM
Engine speed
RR
Rear
ABBREVIATION
DESCRIPTION
SAE
Society of Automotive Engineers, Inc.
SCK
Serial clock
SCR
Selective Catalytic Reduction
SDS
Service Data and Specifications
SRT
System readiness test
SST
Special Service Tools
ABBREVIATION
DESCRIPTION
TC
Turbocharger
TCM
Transmission control module
TCS
Traction control system
TCU
Telematics communication unit
TP
Throttle position
TPMS
Tire pressure monitoring system
TSS
Turbine shaft speed
TWC
Three way catalytic converter
ABBREVIATION
DESCRIPTION
USS
Uphill start support
ABBREVIATION
DESCRIPTION
GI-18
< HOW TO USE THIS MANUAL >
ABBREVIATIONS
V
W
1
2
3
4
5
6
7
ABBREVIATION
DESCRIPTION
VCM
Vehicle control module
VDC
Vehicle dynamics control system
VIN
Vehicle identification number
VSS
Vehicle speed sensor
ABBREVIATION
DESCRIPTION
WOT
Wide open throttle
ABBREVIATION
DESCRIPTION
1
1
1st range first gear
1
2
1st range second gear
1GR
First gear
ABBREVIATION
DESCRIPTION
2
1
2nd range first gear
2
2
2nd range second gear
2GR
Second gear
2WD
2-wheel drive
ABBREVIATION
DESCRIPTION
3GR
Third gear
ABBREVIATION
DESCRIPTION
4GR
Fourth gear
4WAS
Four wheel active steer
4WD
Four wheel drive
ABBREVIATION
DESCRIPTION
5GR
Fifth gear
ABBREVIATION
DESCRIPTION
6GR
Sixth gear
ABBREVIATION
DESCRIPTION
7GR
Seventh gear
TIGHTENING TORQUE OF STANDARD BOLTS
GI-19
< HOW TO USE THIS MANUAL >
C
D
E
F
G
H
I
J
K
L
M
B
GI
N
O
P
TIGHTENING TORQUE OF STANDARD BOLTS
Description
INFOID:0000000012196774
This vehicle has both new standard based on ISO* and previous standard bolts/nuts. There are some differ-
ences between these two types of bolts/ nuts; shape of the head, grade of strength, hexagonal width across
flats and the standard tightening torque.
• For guidance in discriminating, refer to
GI-19, "Tightening Torque Table (New Standard Included)"
• The new standard machine screws and tapping screws have a head of ISO standard torx recess.
• If the tightening torque is not described in the description or figure, refer to
GI-19, "Tightening Torque Table
.
*ISO: International Organization for Standardization
Tightening Torque Table (New Standard Included)
INFOID:0000000012196775
CAUTION:
• The special parts are excluded.
• The bolts/nuts in these tables have a strength (discrimination) number/symbol assigned to the head
or the like. As to the relation between the strength grade in these tables and the strength (discrimi-
nation) number/symbol, refer to “DISCRIMINATION OF BOLTS AND NUTS”.
PREVIOUS STANDARD
CAUTION:
Grade
(Strength
grade)
Bolt
size
Bolt di-
ameter
mm
Hexagonal
width
across flats
mm
Pitch
mm
Tightening torque (Without lubricant)
Hexagon head bolt
Hexagon flange bolt
N·m
kg-m
ft-lb
in-lb
N·m
kg-m
ft-lb
in-lb
4T
M6
6.0
10
1.0
5.5
0.56
4
49
7
0.71
5
62
M8
8.0
12
1.25
13.5
1.4
10
—
17
1.7
13
—
1.0
13.5
1.4
10
—
17
1.7
13
—
M10
10.0
14
1.5
28
2.9
21
—
35
3.6
26
—
1.25
28
2.9
21
—
35
3.6
26
—
M12
12.0
17
1.75
45
4.6
33
—
55
5.6
41
—
1.25
45
4.6
33
—
65
6.6
48
—
M14
14.0
19
1.5
80
8.2
59
—
100
10
74
—
7T
M6
6.0
10
1.0
9
0.92
7
80
11
1.1
8
97
M8
8.0
12
1.25
22
2.2
16
—
28
2.9
21
—
1.0
22
2.2
16
—
28
2.9
21
—
M10
10.0
14
1.5
45
4.6
33
—
55
5.6
41
—
1.25
45
4.6
33
—
55
5.6
41
—
M12
12.0
17
1.75
80
8.2
59
—
100
10
74
—
1.25
80
8.2
59
—
100
10
74
—
M14
14.0
19
1.5
130
13
96
—
170
17
125
—
9T
M6
6.0
10
1.0
11
1.1
8
—
13.5
1.4
10
—
M8 8.0
12
1.25
28
2.9
21
—
35
3.6
26
—
1.0
28
2.9
21
—
35
3.6
26
—
M10
10.0
14
1.5
55
5.6
41
—
80
8.2
59
—
1.25
55
5.6
41
—
80
8.2
59
—
M12
12.0
17
1.75
100
10
74
—
130
13
96
—
1.25
100
10
74
—
130
13
96
—
M14
14.0
19
1.5
170
17
125
—
210
21
155
—
GI-20
< HOW TO USE THIS MANUAL >
TIGHTENING TORQUE OF STANDARD BOLTS
The parts with aluminum or the cast iron washer surface/thread surface are excluded.
NEW STANDARD BASED ON ISO
CAUTION:
1. Use tightening torque with lubricant for the new standard bolts/nuts in principle. Friction coeffi-
cient stabilizer is applied to the new standard bolts/nuts.
2. However, use tightening torque without lubricant for the following cases. Friction coefficient stabi-
lizer is not applied to the following bolts/nuts.
-
Grade 4.8, M6 size bolt, Conical spring washer installed
-
Paint removing nut (Size M6 and M8) for fixing with weld bolt
Grade
(Strength
grade)
Bolt
size
Bolt di-
ameter
mm
Hexagonal
width
across flats
mm
Pitch
mm
Tightening torque
Hexagon head bolt
Hexagon flange bolt
N·m
kg-m
ft-lb
in-lb
N·m
kg-m
ft-lb
in-lb
4.8
(Without
lubricant)
M6
6.0
10
1.0
5.5
0.56
4
49
7
0.71
5
62
M8
8.0
13
1.25
13.5
1.4
10
—
17
1.7
13
—
1.0
13.5
1.4
10
—
17
1.7
13
—
M10
10.0
16
1.5
28
2.9
21
—
35
3.6
26
—
1.25
28
2.9
21
—
35
3.6
26
—
M12
12.0
18
1.75
45
4.6
33
—
55
5.6
41
—
1.25
45
4.6
33
—
65
6.6
48
—
M14
14.0
21
1.5
80
8.2
59
—
100
10
74
—
4.8
(With lu-
bricant)
M6
6.0
10
1.0
4
0.41
3
35
5.5
0.56
4
49
M8
8.0
13
1.25
11
1.1
8
—
13.5
1.4
10
—
1.0
11
1.1
8
—
13.5
1.4
10
—
M10
10.0
16
1.5
22
2.2
16
—
28
2.9
21
—
1.25
22
2.2
16
—
28
2.9
21
—
M12
12.0
18
1.75
35
3.6
26
—
45
4.6
33
—
1.25
35
3.6
26
—
45
4.6
33
—
M14
14.0
21
1.5
65
6.6
48
—
80
8.2
59
—
8.8
(With lu-
bricant)
M6
6.0
10
1.0
8
0.82
6
71
10
1.0
7
89
M8
8.0
13
1.25
21
2.1
15
—
25
2.6
18
—
1.0
21
2.1
15
—
25
2.6
18
—
M10
10.0
16
1.5
40
4.1
30
—
50
5.1
37
—
1.25
40
4.1
30
—
50
5.1
37
—
M12
12.0
18
1.75
70
7.1
52
—
85
8.7
63
—
1.25
70
7.1
52
—
85
8.7
63
—
M14
14.0
21
1.5
120
12
89
—
140
14
103
—
10.9
(With lu-
bricant)
M6
6.0
10
1.0
10
1.0
7
89
12
1.2
9
106
M8
8.0
13
1.25
27
2.8
20
—
32
3.3
24
—
1.0
27
2.8
20
—
32
3.3
24
—
M10
10.0
16
1.5
55
5.6
41
—
65
6.6
48
—
1.25
55
5.6
41
—
65
6.6
48
—
M12
12.0
18
1.75
95
9.7
70
—
110
11
81
—
1.25
95
9.7
70
—
110
11
81
—
M14
14.0
21
1.5
160
16
118
—
180
18
133
—
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст