Nissan Juke F15. Instruction — part 1375
TIRE PRESSURE SENSOR
WT-43
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
2. Install the tire inside beads (1) onto the road wheel (2) in the
position shown in the figure.
3. Install grommet seal to the tire pressure sensor.
CAUTION:
• Never reuse grommet seal.
• Insert grommet seal all the way to the base.
4. Hold tire pressure sensor as shown in the figure, and press the
sensor in the direction shown by arrow (
) to bring it into abso-
lute contact with valve hole. After this, tighten valve nut to the
specified torque.
CAUTION:
• Never reuse valve core and valve cap.
• Check that grommet seal is free of foreign matter.
• Check that grommet seal contacts horizontally with road
wheel.
• Instructionly tighten valve nut all the way to the wheel. (Never
use a power tool to avoid impact.)
5. Set the tire onto the turntable so that the tire changer arm (2) is
at a position approximately 270
° from the tire pressure sensor
(1).
CAUTION:
Be sure that the arm does not contact the tire pressure sen-
sor.
6. Install the tire outer side beads onto the road wheel.
CAUTION:
When installing, check that the tire does not turn together
with the road wheel.
7. Check the tire pressure for all wheels and adjust to the specified
NOTE:
Before adding air, align the tire with the position of the matching mark applied at the time of removal.
8. Install tire to the vehicle. Refer to
WT-39, "Removal and Installation"
9. Perform tire pressure sensor ID registration. Refer to
Snap-in Type
1. Install valve, follow the procedure below.
a. Set the valve to road wheel.
CAUTION:
• Never reuse valve
• Check the valve (1) direction, part (A) of valve must be at 12 o’clock
to the rim of road wheel (2).
JPEIC0105ZZ
JSEIA0466GB
JPEIC0014GB
JSEIA1402ZZ
WT-44
< REMOVAL AND INSTALLATION >
TIRE PRESSURE SENSOR
b. Install the valve (1) to road wheel (2), using a valve inserter (A).
CAUTION:
• Be sure not to damage the road wheel.
• Insert valve all the way to the road wheel.
• Check that valve contacts horizontally with road wheel.
• Check the valve (1) direction, part (A) of valve must be at
12 o’clock to the rim of road wheel (2).
• If the position is not correct, rotate the valve to the correct
position, using a valve inserter.
2. Install the tire pressure sensor, follow the procedure below.
a. Insert the tire pressure sensor (1) to the roll pin (A) of valve (2).
b. Install the stopper (1) until locked in the direction (A) by hands.
CAUTION:
• Never reuse stopper.
• Be sure not to damage the tire pressure sensor.
JSEIA1394ZZ
JSEIA1402ZZ
JSEIA1403ZZ
JSEIA1404ZZ
TIRE PRESSURE SENSOR
WT-45
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
• Be careful with the orientation of stopper (1).
• Pull on the tire pressure sensor to check that the tire pres-
sure sensor is correctly locked on the valve.
• Tire pressure sensor must be oriented tangentially to rim
of road wheel drop-well.
3. Apply bead cream or an equivalent to the tire beads.
4. Install the tire inside beads (1) onto the road wheel (2) in the
position shown in the figure.
5. Set the tire onto the turntable so that the tire changer arm (2) is
at a position approximately 270
° from the tire pressure sensor
(1).
CAUTION:
Be sure that the arm does not contact the tire pressure sen-
sor.
6. Install the tire outer side beads onto the road wheel.
CAUTION:
When installing, check that the tire does not turn together
with the road wheel.
7. Check the tire pressure for all wheels and adjust to the specified
NOTE:
Before adding air, align the tire with the position of the matching mark applied at the time of removal.
8. Install tire to the vehicle. Refer to
WT-39, "Removal and Installation"
9. Perform tire pressure sensor ID registration. Refer to
(A)
: Protrusions of stopper
(B)
: Valve side
JSEIA1405ZZ
JPEIC0105ZZ
JPEIC0014GB
WT-46
< REMOVAL AND INSTALLATION >
TIRE PRESSURE RECEIVER
TIRE PRESSURE RECEIVER
Removal and Installation
INFOID:0000000012201876
REMOVAL
1. Remove the remote keyless entry receiver. (The tire pressure receiver is incorporated into keyless entry
receiver.) Refer to
DLK-174, "Removal and Installation"
INSTALLATION
Install in the reverse order of removal.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст