Nissan Juke F15. Instruction — part 284
FRONT OIL SEAL
DLN-141
< REMOVAL AND INSTALLATION >
[REAR FINAL DRIVE: RTVS]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
3. Align the matching mark (A) of drive pinion with the matching
mark (B) of companion flange (1), and then install the compan-
ion flange.
4. Temporarily tighten drive pinion lock nut to drive pinion, using
the flange wrench (Commercial service tool).
CAUTION:
• Never reuse drive pinion lock nut.
• Apply anti-corrosion oil to the thread and seat of new
drive pinion lock nut.
5. Tighten drive pinion lock nut within the limits of specified torque
so as to keep the pinion bearing preload within a standard val-
ues, using the preload gauge (A) [SST: ST3127S000 (J-25765-
A)].
CAUTION:
• Adjust to the lower limit of the drive pinion lock nut tight-
ening torque first.
• If the preload torque exceeds the specified value, replace
collapsible spacer and tighten it again to adjust. Never
loosen drive pinion lock nut to adjust the preload torque.
6. Check for companion flange runout as follows:
• For companion flange face, fit a dial indicator (1) onto the com-
panion flange face (inner side of the propeller shaft mounting
bolt holes). For inner side of the companion flange, fit a test
indicator (2) to the inner side of companion flange (socket
diameter).
• Rotate companion flange to check for runout.
• If the runout value is outside the runout limit, follow the proce-
dure below to adjust.
- Check for runout while changing the phase between companion flange and drive pinion by 90
° step, and
search for the position where the runout is the minimum.
- If the runout value is still outside of the limit after the phase has been changed, replace companion
flange.
- If the runout value is still outside of the limit after companion flange has been replaced, possible cause
will be an assembly malfunction of drive pinion.
7. Make a stamping for identification of front oil seal replacement frequency. Refer to “Identification stamp of
replacement frequency of front oil seal”.
CAUTION:
Make a stamping after replacing front oil seal.
8. Install electric controlled couplings. Refer to
DLN-145, "Removal and Installation"
.
JSDIA2118ZZ
Total preload torque
: A value that add 0.1 – 0.4
N·m (0.01 – 0.04 kg-m, 1.0 –
3.0 in-lb) to the measured
value before removing.
JSDIA2123ZZ
Companion flange runout : Refer to
.
JSDIA2539ZZ
DLN-142
< REMOVAL AND INSTALLATION >
[REAR FINAL DRIVE: RTVS]
FRONT OIL SEAL
9. Install rear drive shaft. Refer to
RAX-19, "Removal and Installation"
.
10. Install propeller shaft. Refer to
DLN-124, "Removal and Installation"
11. Refill gear oil to the final drive and check level. Refer to
12. Check the final drive for oil leakage. Refer to
SIDE OIL SEAL
DLN-143
< REMOVAL AND INSTALLATION >
[REAR FINAL DRIVE: RTVS]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
SIDE OIL SEAL
Exploded View
INFOID:0000000012199505
Removal and Installation
INFOID:0000000012199506
REMOVAL
1. Drain gear oil. Refer to
.
2. Remove electric controlled couplings. Refer to
DLN-145, "Removal and Installation"
3. Remove side oil seal with the suitable oil seal remover.
CAUTION:
Never damage gear carrier and rear cover.
INSTALLATION
1.
Electric controlled coupling (right)
2.
Side oil seal (right)
3.
Rear final drive assembly
4.
Side oil seal (left)
5.
Electric controlled coupling (left)
A.
Oil seal lip
: Always replace after every disassembly.
: Apply multi purpose grease
: Apply gear oil.
JSDIA2233GB
JSDIA2234ZZ
DLN-144
< REMOVAL AND INSTALLATION >
[REAR FINAL DRIVE: RTVS]
SIDE OIL SEAL
1. Install side oil seal (right) until it becomes flush with the gear car-
rier end, using the drift (A) [SST: ST33400001 (J-26082)].
CAUTION:
• Never reuse oil seal.
• When installing, never incline oil seal.
• Apply multi-purpose grease onto oil seal lip, and gear oil
onto the circumference of oil seal.
2. Install side oil seal (left) until it becomes flush with the gear car-
rier end, using the drift (A) [SST: KV38100500 (
—
)].
CAUTION:
• Never reuse oil seal.
• When installing, never incline oil seal.
• Apply multi-purpose grease onto oil seal lip, and gear oil
onto the circumference of oil seal.
3. Install electric controlled couplings. Refer to
4. Refill gear oil to the final drive and check level. Refer to
5. When oil leaks while removing, check oil level after the installa-
.
JSDIA2235ZZ
JSDIA2236ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст