Nissan Juke F15. Instruction — part 231
DLK-104
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
IGN OFF INTERLOCK DOOR UNLOCK FUNCTION DOES NOT OPERATE
IGN OFF INTERLOCK DOOR UNLOCK FUNCTION DOES NOT OPERATE
Diagnosis Procedure
INFOID:0000000012196684
1.
CHECK “AUTOMATIC LOCK/UNLOCK SELECT” SETTING IN “WORK SUPPORT”
1. Select “DOOR LOCK” of “BCM” using CONSULT.
2. Select “AUTOMATIC LOCK/UNLOCK SELECT” in “WORK SUPPORT” mode.
3. Check “AUTOMATIC LOCK/UNLOCK SELECT” in “WORK SUPPORT”.
DLK-26, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Set “AUTOMATIC LOCK/UNLOCK SELECT” in “WORK SUPPORT”.
2.
CHECK “AUTOMATIC DOOR UNLOCK SELECT” SETTING IN “WORK SUPPORT”
1. Select “DOOR LOCK” of “BCM” using CONSULT.
2. Select “AUTOMATIC DOOR UNLOCK SELECT” in “WORK SUPPORT” mode.
3. Check “AUTOMATIC DOOR UNLOCK SELECT” in “WORK SUPPORT”.
DLK-26, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Set “AUTOMATIC DOOR UNLOCK SELECT” in “WORK SUPPORT”.
3.
REPLACE BCM
1. Replace BCM. Refer to
BCS-94, "Removal and Installation"
.
2. Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-45, "Intermittent Incident"
.
P RANGE INTERLOCK DOOR LOCK/UNLOCK FUNCTION DOES NOT OPER-
ATE
DLK-105
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
P RANGE INTERLOCK DOOR LOCK/UNLOCK FUNCTION DOES NOT OP-
ERATE
Diagnosis Procedure
INFOID:0000000012196685
1.
CHECK “AUTOMATIC LOCK/UNLOCK SELECT” SETTING IN “WORK SUPPORT”
1. Select “DOOR LOCK” of “BCM” using CONSULT.
2. Select “AUTOMATIC LOCK/UNLOCK SELECT” in “WORK SUPPORT” mode.
3. Check “AUTOMATIC LOCK/UNLOCK SELECT” in “WORK SUPPORT”.
DLK-26, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Set “AUTOMATIC LOCK/UNLOCK SELECT” in “WORK SUPPORT”.
2.
CHECK “AUTOMATIC DOOR LOCK SELECT” SETTING IN “WORK SUPPORT”
1. Select “DOOR LOCK” of “BCM” using CONSULT.
2. Select “AUTOMATIC DOOR LOCK SELECT” in “WORK SUPPORT” mode.
3. Check “AUTOMATIC DOOR LOCK SELECT” in “WORK SUPPORT”.
DLK-26, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Set “AUTOMATIC DOOR LOCK SELECT” in “WORK SUPPORT”.
3.
CHECK “AUTOMATIC DOOR UNLOCK SELECT” SETTING IN “WORK SUPPORT”
1. Select “DOOR LOCK” of “BCM” using CONSULT.
2. Select “AUTOMATIC DOOR UNLOCK SELECT” in “WORK SUPPORT” mode.
3. Check “AUTOMATIC DOOR UNLOCK SELECT” in “WORK SUPPORT”.
DLK-26, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)"
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Set “AUTOMATIC DOOR UNLOCK SELECT” in “WORK SUPPORT”.
4.
REPLACE BCM
1. Replace BCM. Refer to
BCS-94, "Removal and Installation"
.
2. Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-45, "Intermittent Incident"
.
DLK-106
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
HAZARD AND BUZZER REMINDER DOES NOT OPERATE
HAZARD AND BUZZER REMINDER DOES NOT OPERATE
Diagnosis Procedure
INFOID:0000000012196686
1.
CHECK DTC WITH BCM AND COMBINATION METER
Check that DTC is not detected with BCM and combination meter.
Is the inspection result normal?
YES
>> GO TO 2.
NO-1 >> Refer to
NO-2 >> Refer to
. (Combination meter)
2.
CHECK “HAZARD ANSWER BACK” SETTING IN “WORK SUPPORT”
1. Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2. Select “HAZARD ANSWER BACK” in “WORK SUPPORT” mode.
3. Check the “HAZARD ANSWER BACK” in “WORK SUPPORT”.
DLK-28, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Set “HAZARD ANSWER BACK” in “WORK SUPPORT”.
3.
CHECK “ANS BACK I-KEY LOCK” SETTING IN “WORK SUPPORT”
1. Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2. Select “ANS BACK I-KEY LOCK” in “WORK SUPPORT” mode.
3. Check the “ANS BACK I-KEY LOCK” in “WORK SUPPORT”.
DLK-28, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Set “ANS BACK I-KEY LOCK” in “WORK SUPPORT”.
4.
CHECK “ANS BACK I-KEY UNLOCK” SETTING IN “WORK SUPPORT”
1. Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2. Select “ANS BACK I-KEY UNLOCK” in “WORK SUPPORT” mode.
3. Check the “ANS BACK I-KEY UNLOCK” in “WORK SUPPORT”.
DLK-28, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Set “ANS BACK I-KEY UNLOCK” in “WORK SUPPORT”.
5.
CHECK HAZARD FUNCTION
Check hazard function.
DLK-80, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace the malfunctioning parts.
6.
CHECK INTELLIGENT KEY WARNING BUZZER
Check Intelligent Key warning buzzer.
DLK-82, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Repair or replace the malfunctioning parts.
7.
REPLACE BCM
1. Replace BCM. Refer to
BCS-94, "Removal and Installation"
.
2. Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
HAZARD AND BUZZER REMINDER DOES NOT OPERATE
DLK-107
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
NO
>> Check intermittent incident. Refer to
GI-45, "Intermittent Incident"
.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст