Nissan Juke F15. Instruction — part 692
EM-322
< SERVICE DATA AND SPECIFICATIONS (SDS)
[MR EXCEPT FOR NISMO RS MODELS]
SERVICE DATA AND SPECIFICATIONS (SDS)
UNDERSIZE TABLE
Unit: mm (in)
MAIN BEARING OIL CLEARANCE
Unit: mm (in)
01
UPR
1.996 - 1.999 (0.0786 - 0.0787)
Black - Black
Grade and color are different
between upper and lower bear-
ings.
LWR
1.999 - 2.002 (0.0787 - 0.0788)
Brown - Brown
12
UPR
1.999 - 2.002 (0.0787 - 0.0788)
Brown - Brown
LWR
2.002 - 2.005 (0.0788 - 0.0789)
Green - Green
23
UPR
2.002 - 2.005 (0.0788 - 0.0789)
Green - Green
LWR
2.005 - 2.008 (0.0789 - 0.0791)
Yellow - Yellow
34
UPR
2.005 - 2.008 (0.0789 - 0.0791)
Yellow - Yellow
LWR
2.008 - 2.011 (0.0791 - 0.0792)
Blue - Blue
45
UPR
2.008 - 2.011 (0.0791 - 0.0792)
Blue - Blue
LWR
2.011 - 2.014 (0.0792 - 0.0793)
Pink - Pink
56
UPR
2.011 - 2.014 (0.0792 - 0.0793)
Pink - Pink
LWR
2.014 - 2.017 (0.0793 - 0.0794)
Purple - Purple
67
UPR
2.014 - 2.017 (0.0793 - 0.0794)
Purple - Purple
LWR
2.017 - 2.020 (0.0794 - 0.0795)
White - White
Items
Thickness
Main journal diameter
US 0.25 (0.0098)
2.126 - 2.134 (0.0837 - 0.0840)
Grind so that bearing clearance is the specified value.
Main bearing oil clearance
Standard
No. 1 and 4
0.024 - 0.034 (0.0009 - 0.0013)
No. 2, 3 and 5
0.012 - 0.022 (0.0005 - 0.0009)
Limit
0.065 (0.0026)
EX-1
ENGINE
C
D
E
F
G
H
I
J
K
L
M
SECTION
EX
A
EX
N
O
P
CONTENTS
EXHAUST SYSTEM
MR16DDT
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precautions for Removing Battery Terminal . . .....
Removal and Installation . . . . . . . . . . ...
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Special Service Tools . . . . . . . . . . . ....
Commercial Service Tools . . . . . . . . . ....
PERIODIC MAINTENANCE . . . . . . .
EXHAUST SYSTEM . . . . . . . . . . ...
Inspection . . . . . . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . .
EXHAUST SYSTEM . . . . . . . . . . ...
Exploded View . . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . .
EX-2
< PRECAUTION >
[MR16DDT ]
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precautions for Removing Battery Terminal
INFOID:0000000012197609
• When removing the 12V battery terminal, turn OFF the ignition
switch and wait at least 30 seconds.
NOTE:
ECU may be active for several tens of seconds after the ignition
switch is turned OFF. If the battery terminal is removed before ECU
stops, then a DTC detection error or ECU data corruption may
occur.
• For vehicles with the 2-batteries, be sure to connect the main bat-
tery and the sub battery before turning ON the ignition switch.
NOTE:
If the ignition switch is turned ON with any one of the terminals of
main battery and sub battery disconnected, then DTC may be
detected.
• After installing the 12V battery, always check "Self Diagnosis Result" of all ECUs and erase DTC.
NOTE:
The removal of 12V battery may cause a DTC detection error.
Removal and Installation
INFOID:0000000012197610
CAUTION:
• Be sure to use genuine exhaust system parts or equivalents which are specially designed for heat
resistance, corrosion resistance, and shape.
• Perform the operation with the exhaust system fully cooled down because the system will be hot
just after engine stops.
• Be careful not to cut your hand on the heat insulator edge.
SEF289H
PREPARATION
EX-3
< PREPARATION >
[MR16DDT ]
C
D
E
F
G
H
I
J
K
L
M
A
EX
N
P
O
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000012197611
The actual shapes of TechMate tools may differ from those of special service tools illustrated here.
Commercial Service Tools
INFOID:0000000012197612
Tool number
(TechMate No.)
Tool name
Description
KV10114400
(J-38365)
Heated oxygen sensor wrench
Loosening or tightening heated oxygen sen-
sor 2 ( 2WD models)
a: For 22 mm (0.87 in) width hexagon nut
S-NT636
Tool name
Description
Power tool
Loosening nuts and bolts
Heated oxygen sensor thread cleaner
Reconditioning the exhaust system threads
before installing a new heated oxygen sensor
(Use with anti-seize lubricant shown below.)
A: J-43897-18 [18 mm (0.71 in) dia.] for zir-
conia heated oxygen sensor
B: J-43897-12 [12 mm (0.47 in) dia.] for tita-
nia heated oxygen sensor
C: Mating surface shave cylinder
D: Flutes
Anti-seize lubricant (Permatex 133AR
or equivalent meeting MIL specifica-
tion MIL-A-907)
Lubricating heated oxygen sensor thread
cleaner when reconditioning exhaust system
threads
PBIC0190E
JPBIA0238ZZ
AEM489
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст