Nissan Juke F15. Instruction — part 308
COMPONENT PARTS
EC-45
< SYSTEM DESCRIPTION >
[MR FOR NISMO RS MODELS]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
Battery temperature sensor is integrated in battery current sensor.
The sensor measures temperature around the battery.
The electrical resistance of the thermistor decreases as temperature
increases.
<Reference data>
*: These data are reference values and are measured between battery temperature
sensor signal terminal and sensor ground.
Malfunction Indicator lamp (MIL)
INFOID:0000000012197655
The Malfunction Indicator lamp (MIL) is located on the combination
meter.
The MIL will illuminate when the ignition switch is turned ON without
the engine running. This is a bulb check.
When the engine is started, the MIL should turn OFF. If the MIL
remains illuminated, the on board diagnostic system has detected an
engine system malfunction.
For details, refer to
EC-81, "DIAGNOSIS DESCRIPTION : Malfunc-
.
Oil Pressure Warning Lamp
INFOID:0000000012197656
Oil pressure warning lamp is located on the combination meter.
It indicates the low pressure of the engine oil and the malfunction of
the engine oil pressure system.
Combination meter turns the oil pressure warning lamp ON/OFF
according to the oil pressure warning lamp signal received from
ECM via CAN communication.
Refrigerant Pressure Sensor
INFOID:0000000012197657
The refrigerant pressure sensor is installed at the condenser of the air conditioner system. The sensor uses an
electrostatic volume pressure transducer to convert refrigerant pressure to voltage. The voltage signal is sent
to ECM, and ECM controls cooling fan system.
Stop Lamp Switch & Brake Pedal Position Switch
INFOID:0000000012197658
Stop lamp switch and brake pedal position switch are installed to brake pedal bracket.
ECM detects the state of the brake pedal by those two types of input (ON/OFF signal).
Temperature [
°C (°F)]
Voltage
*
(V)
Resistance (k
Ω)
25 (77)
3.333
1.9 - 2.1
90 (194)
0.969
0.222 - 0.258
SEF012P
JSBIA1315ZZ
PBIA8559J
PBIB2657E
EC-46
< SYSTEM DESCRIPTION >
[MR FOR NISMO RS MODELS]
COMPONENT PARTS
Clutch Pedal Position Switch
INFOID:0000000012197659
When the clutch pedal is depressed, the clutch pedal position switch turns OFF and the clutch pedal position
switch signal is sent to the ECM. The ECM judges the clutch pedal conditions via the signal (ON or OFF).
ASCD Steering Switch
INFOID:0000000012197660
ASCD steering switch has variant values of electrical resistance for each button. ECM reads voltage variation
of switch, and determines which button is operated.
Information Display
INFOID:0000000012197661
The operation mode of the ASCD is indicated on the information display in the combination meter.
ECM transmits the status signal to the combination meter via CAN communication according to ASCD opera-
tion.
Brake pedal
Brake pedal position switch
Stop lamp switch
Released
ON
OFF
Depressed
OFF
ON
STRUCTURE AND OPERATION
EC-47
< SYSTEM DESCRIPTION >
[MR FOR NISMO RS MODELS]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
STRUCTURE AND OPERATION
Positive Crankcase Ventilation
INFOID:0000000012197662
This system returns blow-by gas to the intake manifold.
The positive crankcase ventilation (PCV) valve is provided to conduct crankcase blow-by gas to the intake
manifold.
During partial throttle operation of the engine, the intake manifold sucks the blow-by gas through the PCV
valve.
Normally, the capacity of the valve is sufficient to handle any blow-by and a small amount of ventilating air.
The ventilating air is then drawn from the air inlet tubes into the crankcase. In this process the air passes
through the hose connecting air inlet tubes to rocker cover.
Under full-throttle condition, the manifold vacuum is insufficient to draw the blow-by flow through the valve.
The flow goes through the hose connection in the reverse direction.
On vehicles with an excessively high blow-by, the valve does not
meet the requirement. This is because some of the flow will go
through the hose connection to the air inlet tubes under all condi-
tions.
PBIB0492E
PBIB1588E
EC-48
< SYSTEM DESCRIPTION >
[MR FOR NISMO RS MODELS]
STRUCTURE AND OPERATION
On Board Refueling Vapor Recovery (ORVR)
INFOID:0000000012197663
From the beginning of refueling, the air and vapor inside the fuel tank go through refueling EVAP vapor cut
valve and EVAP/ORVR line to the EVAP canister. The vapor is absorbed by the EVAP canister and the air is
released to the atmosphere.
When the refueling has reached the full level of the fuel tank, the refueling EVAP vapor cut valve is closed and
refueling is stopped because of auto shut-off. The vapor which was absorbed by the EVAP canister is purged
during driving.
WARNING:
When conducting inspections below, be sure to observe the following:
• Put a “CAUTION: FLAMMABLE” sign in workshop.
• Do not smoke while servicing fuel system. Keep open flames and sparks away from work area.
• Be sure to furnish the workshop with a CO
2
fire extinguisher.
CAUTION:
• Before removing fuel line parts, carry out the following procedures:
- Put drained fuel in an explosion-proof container and put lid on securely.
- Release fuel pressure from fuel line. Refer to
.
- Disconnect battery ground cable.
• Always replace O-ring when the fuel gauge retainer is removed.
• Do not kink or twist hose and tube when they are installed.
• Do not tighten hose and clamps excessively to avoid damaging hoses.
• After installation, run engine and check for fuel leaks at connection.
• Do not attempt to top off the fuel tank after the fuel pump nozzle shuts off automatically.
Continued refueling may cause fuel overflow, resulting in fuel spray and possibly a fire.
JMBIA1930GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст