Nissan Juke F15. Instruction — part 1340
TM-550
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
CONTROL CABLE
4. Disengage the pawls (B) of the grommet (A), and pull down-
wards to remove.
5. Remove the battery and battery mounting bracket assembly.
PG-105, "Removal and Installation"
6. Remove the control cable nut (
) and remove the control cable
(1) from the instruction lever (2).
7. Remove the lock plate (1) and remove the control cable (2) from
bracket (3).
8. Remove center muffler from the mounting rubber and lower the
center muffler downward. Refer to
9. Remove heat plate.
10. Remove the control cable (1) from the bracket (2).
11. Remove the control cable from the vehicle.
INSTALLATION
Note the following, and install in the reverse order of removal.
• After installing control cable, adjust it. Refer to
TM-551, "Inspection and Adjustment"
.
JSDIA1809ZZ
: Vehicle front
JSDIA6039ZZ
: Vehicle front
JSDIA5184ZZ
:Vehicle front
JPDIA0107ZZ
CONTROL CABLE
TM-551
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
• From below the vehicle, press the grommet (A) into place until the
pawls (B) make a click sound.
CAUTION:
• Place the grommet on the floor, then fasten it in place from
below the vehicle.
• Check that pulling down on the grommet does not discon-
nect it.
• Pay attention to the following when connecting the control cable to the CVT shift selector.
1. When connecting the control cable (1) to the CVT shift selector
assembly (2), face the grooved surface of the rib (A) up and
insert the control cable until it stops.
2. Install the socket (A) onto the CVT shift selector.
CAUTION:
• Place the socket onto the CVT shift lever, then fasten it in
place from above.
• Check that the pulling on the socket does not disconnect
it.
Inspection and Adjustment
INFOID:0000000012201243
ADJUSTMENT OF CONTROL CABLE
1. Shift the selector lever to the “P” position.
CAUTION:
Rotate the wheels at least a quarter turn and be certain the Park position mechanism is fully
engaged.
2. Loosen nut and set instruction lever to the “P” position.
CAUTION:
Never apply force to the instruction lever.
3. Tighten the nut to the specified torque. Refer to
CAUTION:
In tightening, fix the instruction lever.
INSPECTION AFTER INSTALLATION
Check the CVT position. Refer to
JSDIA1809ZZ
JSDIA1624ZZ
JSDIA1810ZZ
JSDIA5177ZZ
TM-552
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
PADDLE SHIFTER
PADDLE SHIFTER
Exploded View
INFOID:0000000012201244
Removal and Installation
INFOID:0000000012201245
REMOVAL
1. Park the vehicle on a level surface.
2. Remove the driver air bag module. Refer to
SR-12, "Removal and Installation"
3. Remove the steering wheel. Refer to
ST-9, "Removal and Installation"
4. Remove the column cover. Refer to
IP-13, "Removal and Installation"
1.
Steering column assembly
2.
Paddle shifter (shift-down switch)
3.
Paddle shifter (shift-up switch)
: N·m (kg-m, in-lb)
AWDIA0557GB
PADDLE SHIFTER
TM-553
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
5. Remove the paddle shifter connector (C) and (D) from paddle
shifter.
6. Remove the paddle shifter mounting bolts (E) and nuts (F).
7. Remove the paddle shifter from the steering column assembly.
INSTALLATION
Installation is in the reverse order of removal.
A
: Side of paddle shifter (shift-down switch)
B
: Side of paddle shifter (shift-up switch)
AWDIA0563ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст