Nissan Juke F15. Instruction — part 237
DLK-128
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
HOOD
If the clearance and the surface height are out of specification, adjust them according to the procedures
shown below.
Unit: mm (in)
1. Remove front center grille. Refer to
EXT-26, "Removal and Installation"
2. Remove hood lock assembly.
3. Remove front bumper fascia. Refer to
EXT-17, "Removal and Installation"
.
4. Remove front combination lamp (LH and RH). Refer to
EXL-100, "Removal and Installation"
EXL-211, "Removal and Installation"
(halogen type).
5. Remove front fender assembly (LH and RH). Refer to
DLK-133, "Removal and Installation"
6. Loosen hood hinge mounting bolts.
7. Temporarily install front fender assembly (LH and RH), front combination lamp (LH and RH) and front
bumper fascia.
8. Adjust the clearance of hood assembly, front fender assembly (LH and RH), front combination lamp (LH
and RH) and front bumper fascia according to the specified value, by moving hood hinge (body side).
9. Temporarily tighten hood hinge (LH and RH).
10. Remove front bumper fascia, front combination lamp (LH and RH) and front fender assembly (LH and
RH).
11. Tighten hood hinge (LH and RH) to the specified torque.
12. Install front fender assembly (LH and RH). Refer to
DLK-133, "Removal and Installation"
.
13. Install front combination lamp (LH and RH). Refer to
EXL-100, "Removal and Installation"
EXL-211, "Removal and Installation"
(halogen type).
14. Install front bumper fascia. Refer to
EXT-17, "Removal and Installation"
.
15. Adjust the surface height of hood assembly, front fender assembly, and front combination lamp according
to the specified value, by rotating hood bumper rubber.
16. Position hood lock assembly and engage hood striker. Check hood lock assembly and hood striker for
looseness.
17. Move hood lock assembly laterally until the center of hood striker and hood lock assembly are vertical
when viewed from the front.
18. After adjustment, tighten lock bolts to the specified torque.
19. Open hood. Rotate bumper rubber counterclockwise between half a turn and three-quarters of a turn.
20. Check that secondary latch is securely engaged with secondary hood striker from the dead load of the
hood assembly.
21. Check that primary latch is securely engaged with primary hood striker when hood assembly is closed
[free-fall from approximately 200 mm (7.874 in) height].
CAUTION:
Never free-fall hood assembly from a height of 300 (11.811 in) mm or more.
22. Install front center grille. Refer to
EXT-26, "Removal and Installation"
CAUTION:
After installation, apply touch-up paint (the body color) onto the heads of hood hinge mounting
bolts and nuts.
Portion
Standard
Difference
(RH/LH,
MAX)
Hood – Front
bumper fascia
A – A
E
Clearance
2.0 – 6.0 (0.079 – 0.236)
< 2.5 (0.098)
F Surface height
(-2.0) – (+2.0) [(-0.079) – (+0.079)]
< 2.5 (0.098)
Hood – Front combi-
nation lamp
B – B G
Clearance
2.0 – 6.0 (0.079 – 0.236)
< 2.5 (0.098)
Hood – Front combi-
nation lamp
C – C H
Clearance
2.0 – 6.0 (0.079 – 0.236)
< 2.5 (0.098)
Hood – Front fender
D – D
I
Clearance
2.5 – 4.5 (0.098 – 0.177)
< 1.5 (0.059)
J Surface height
(-2.0) – (0.0) [(-0.079) – (0.000)]
< 1.5 (0.059)
HOOD
DLK-129
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
HOOD SUPPORT ROD
HOOD SUPPORT ROD : Removal and Installation
INFOID:0000000012196705
REMOVAL
CAUTION:
Two workers are required to support the hood.
1. Support hood assembly with a suitable material to prevent it from falling.
WARNING:
Injury may occur if hood assembly is not supported by the proper material when removing hood
assembly.
2. Pull hood support rod from grommet and remove.
INSTALLATION
Install in the reverse order of removal.
DLK-130
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
RADIATOR CORE SUPPORT
RADIATOR CORE SUPPORT
MR16DDT
MR16DDT : Exploded View
INFOID:0000000012196706
*1
: Except for NISMO/NISMO RS models
*2
: For NISMO/NISMO RS models
MR16DDT : Removal and Installation
INFOID:0000000012196707
RADIATOR CORE SUPPORT UPPER
Removal
1. Remove front bumper fascia. Refer to
EXT-17, "Removal and Installation"
.
2. Remove front combination lamp (LH and RH). Refer to
EXL-100, "Removal and Installation"
EXL-211, "Removal and Installation"
(halogen type).
3. Remove headlamp (LH and RH). Refer to
EXL-96, "Removal and Installation"
(halogen type).
4. Disconnect crash zone sensor harness connector. Refer to
SR-24, "Removal and Installation"
CAUTION:
Turn ignition switch OFF, disconnect battery negative terminal and then wait for at least 3 minutes.
5. Remove hood lock and hood lock cable fixing clip. Refer to
DLK-155, "HOOD LOCK CONTROL CABLE :
.
1.
Radiator core support upper
2.
Air guide (RH)
*1
3.
Radiator core support lower
4.
Air guide (LH)
*1
5.
Air guide (RH)
*2
6.
Air guide (LH)
*2
: N·m (kg-m, ft-lb)
JMKIB4585GB
RADIATOR CORE SUPPORT
DLK-131
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
6. Remove horn bracket. Refer to
HRN-7, "Removal and Installation"
7. Remove upper fixing clips (2) of air guide (LH and RH) (1).
8. Remove hood support rod. Refer to
DLK-129, "HOOD SUPPORT ROD : Removal and Installation"
.
9. Remove mounting bolts, and then remove radiator core support upper.
Installation
Install in the reverse order of removal.
RADIATOR CORE SUPPORT LOWER
Removal
1. Remove front bumper fascia. Refer to
EXT-17, "Removal and Installation"
.
2. Remove lower fixing clips (2) of radiator side seal (LH and RH)
(1).
3. Using strings (A), hang inlet hose (1) and inlet hose (2) together
with charge air cooler.
CAUTION:
Never damage inlet hoses and charge air cooler.
4. Support lower side radiator using a floor jack (A) and wooden
blocks (B).
CAUTION:
Never damage radiator.
5. Remove mounting bolts, and then remove radiator core support lower.
JMKIA6023ZZ
JMKIA6024ZZ
JMKIA6025ZZ
JMKIA6026ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст