Nissan Juke F15. Instruction — part 658
EM-186
< PERIODIC MAINTENANCE >
[MR EXCEPT FOR NISMO RS MODELS]
DRIVE BELT
Inspection
INFOID:0000000012197372
INSPECTION
WARNING:
Perform this step when engine is stopped.
• Check that the indicator (C) (notch on fixed side) of drive belt auto-tensioner is within the possible use range
(A) in the figure.
NOTE:
• Check the drive belt auto-tensioner indication when the engine is cold.
• When new drive belt is installed, the indicator (notch on fixed side) should be within the range (B) in the fig-
ure.
• Visually check entire drive belt for wear, damage or cracks.
• If the indicator (notch on fixed side) is out of the possible use range or belt is damaged, replace drive belt.
Adjustment
INFOID:0000000012197373
1.
Alternator
2.
Drive belt auto tensioner
3.
Crankshaft pulley
4.
A/C compressor
5.
Water pump
6.
Drive belt
A. Possible use range
B. Range when new drive belt is in-
stalled
C. Indicator
JSBIA5907ZZ
Refer to :
AIR CLEANER FILTER
EM-187
< PERIODIC MAINTENANCE >
[MR EXCEPT FOR NISMO RS MODELS]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
AIR CLEANER FILTER
Exploded View
INFOID:0000000012197374
Removal and Installation
INFOID:0000000012197375
REMOVAL
1.
Mass air flow sensor
2.
Gasket
3.
Clamp
4.
Air duct
5.
Clamp
6.
Air cleaner case
7.
Mount rubber
8.
Air cleaner filter
9.
Element case
10. Inlet air duct (lower)
11. Grommet
12. Inlet air duct (upper)
13. Grommet
14. Bracket
15. Mount rubber
A.
To exhaust manifold and turbocharg-
er assembly
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
JSBIA5756GB
EM-188
< PERIODIC MAINTENANCE >
[MR EXCEPT FOR NISMO RS MODELS]
AIR CLEANER FILTER
1. Remove the inlet air duct (upper) (1).
2. Unhook the tabs (A) of both ends of the air cleaner cover.
3. Remove the air cleaner filter (1) and air cleaner body (2) from
the air cleaner case.
4. Remove the air cleaner filter from the air cleaner body.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Fixing clips shall be fixed after inserting air cleaner body protrusion to air cleaner case notch hole.
• Make sure that whether air cleaner body has been firmly installed by shaking it.
Inspection (Viscous Paper Type)
INFOID:0000000012961777
INSPECTION AFTER REMOVAL
Examine with eyes that there is no stain, clogging, or damage on air cleaner element.
• Remove dusts (such as dead leafs) on air cleaner element surface and inside cleaner case.
• If clogging or damage is observed, replace the air cleaner element.
CAUTION:
Never clean the viscous paper type air cleaner element by blowing as there is a risk of deterioration of
its performance
MAINTENANCE INTERVAL
MA-7, "Introduction of Periodic Maintenance"
JPBIA4352ZZ
JPBIA4353ZZ
SPARK PLUG
EM-189
< PERIODIC MAINTENANCE >
[MR EXCEPT FOR NISMO RS MODELS]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
SPARK PLUG
Exploded View
INFOID:0000000012197376
Removal and Installation
INFOID:0000000012197377
REMOVAL
1. Remove the engine cover. Refer to
.
2. Remove air inlet tube 2. Refer to
EM-194, "Removal and Installation"
3. Remove the ignition coil. Refer to
1.
Rocker cover protector
2.
O-ring
3.
Positive Crank Ventilation (PCV)
valve
4.
PCV hose
5.
Clamp
6.
Rocker cover gasket
7.
Rocker cover
8.
Clamp
9.
PCV hose
10. Oil filler cap
11. Spark plug
12. Ignition coil
A.
To intake manifold
B.
Comply with the assembly procedure
when tightening.
C.
To turbocharger inlet tube
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
JSBIA5757GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст