Nissan Juke F15. Instruction — part 779
FRONT DRIVE SHAFT
FAX-55
< REMOVAL AND INSTALLATION >
[TYPE 1]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
6. To prevent the deformation of the boot, adjust the boot installation length to the value shown below (L) by
inserting the suitable tool into the inside of boot from the large diameter side of boot and discharging
inside air.
CAUTION:
• If the boot installation length exceeds the standard, it may cause breakage of the boot.
• Be careful not to touch the inside of the boot with the tip of tool.
7. Install boot bands securely.
CAUTION:
Never reuse boot bands.
a. Put boot band in the groove on drive shaft boot. Then fit pawls
(
) into holes to temporary installation.
NOTE:
For the large diameter side, fit projection (A) and guide slit (B) at
first.
b. Pinch projection on the band with suitable pliers to tighten band.
c. Insert the tip of band into the lower part of pawl (marked with
dotted circle) as shown in the figure.
8. Check that displacement does not occur when boot is rotated with the housing assembly fixed.
CAUTION:
• If displacement occurs, reinstall band.
• Never reuse boot band.
9. Install dynamic damper, follow the procedure described below.
a. Install dynamic damper to shaft.
b. Secure dynamic damper with bands in the following specified
position (A) when installing.
CAUTION:
Never reuse bands.
L
: Refer to
JPDIF0157ZZ
JPDIF0158ZZ
A :
JPDIF0178ZZ
FAX-56
< REMOVAL AND INSTALLATION >
[TYPE 1]
FRONT DRIVE SHAFT
c.
Install boot bands securely as showin in the figure.
10. Install boot to the wheel side. Refer to
FAX-22, "AWD : Removal and Installation"
AWD : Inspection
INFOID:0000000012201540
INSPECTION AFTER INSTALLATION
1. Check wheel sensor harness for proper connection. Refer to
BRC-147, "FRONT WHEEL SENSOR :
.
2. Check the wheel alignment. Refer to
.
3. Adjust neutral position of steering angle sensor. Refer to
.
PDIA1188J
SERVICE DATA AND SPECIFICATIONS (SDS)
FAX-57
< SERVICE DATA AND SPECIFICATIONS (SDS)
[TYPE 1]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Wheel Bearing
INFOID:0000000012201541
Drive Shaft
INFOID:0000000012201542
2WD (Except for NISMO RS models)
*: For measuring position, refer to
FAX-32, "2WD : Disassembly and Assembly"
2WD (For NISMO RS models)
*: For measuring position, refer to
FAX-32, "2WD : Disassembly and Assembly"
AWD
*: For measuring position, refer to
FAX-32, "2WD : Disassembly and Assembly"
Item
Standard
Axial end play
0.05 mm (0.002 in) or less
Item
Standard
Left side
Right side
Grease quantity
Wheel side
115 – 125 g (4.05 – 4.40 oz)
Transaxle side
132 – 142 g (4.65 – 5.00 oz)
Boots installed length
*
Wheel side
97.1 mm (3.82 in)
Transaxle side
85.0 mm (3.35 in)
Dimension of dynamic damper
*
267 –273 mm (10.51 – 10.75 in)
257 – 263 mm (10.12 – 10.35 in)
Item
Standard
Left side
Right side
Grease quantity
Wheel side
115 – 135 g (4.06 – 4.76 oz)
Transaxle side
215 – 235 g (7.58 – 8.28 oz)
Boots installed length
*
Wheel side
133.5 mm (5.26 in)
Transaxle side
185.1mm (6.34 in)
173.1mm (6.81 in)
Dimension of dynamic damper
*
249 – 255 mm (9.80 – 10.04 in)
252 – 258 mm (9.92 – 10.16 in)
Item
Standard
Left side
Right side
Grease quantity
Wheel side
88 – 108 g (3.01 – 3.80 oz)
Transaxle side
114 – 124 g (4.02 – 4.37 oz)
Boots installed length
*
Wheel side
95.4 mm (3.75 in)
Transaxle side
93.2 mm (3.66 in)
Dimension of dynamic damper
*
267 – 273 mm (10.51 – 10.75 in)
FAX-58
< HOW TO USE THIS MANUAL >
[TYPE 2]
HOW TO USE THIS SECTION
HOW TO USE THIS MANUAL
HOW TO USE THIS SECTION
Information
INFOID:0000000012990169
Service information
Model information
TYPE 1
For NISMO models
TYPE 2
Except for NISMO models
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст