Nissan Juke F15. Instruction — part 193
MULTI-WAY CONTROL VALVE
CO-55
< REMOVAL AND INSTALLATION >
[MR EXCEPT FOR NISMO RS MODELS]
C
D
E
F
G
H
I
J
K
L
M
A
CO
N
P
O
Be sure to perform this operation when coolant temperature is cold.
2. Remove the engine cover. Refer to
EM-191, "Removal and Installation"
.
3. Remove the battery. Refer to
PG-105, "Removal and Installation"
.
4. Remove the air duct inlet (upper), element case, and air cleaner case. Refer to
.
5. Disconnect the radiator hose (upper) from the water outlet adapter. Refer to
6. Disconnect the reservoir tank hose from the water outlet adapter. Refer to
.
7. Disconnect the water hose from the water outlet adapter. Refer to
8. Disconnect the water outlet hose and the water outlet adapter.
9. Remove the harness clamps (A) and harness clips (B).
10. Remove the breather hose (1) and bracket mounting bolt (A),
and then remove the bracket (2).
11. Remove the bracket mounting bolt (A) and move the engine har-
ness (1) to a location where it does not interfere with work.
12. Disconnect harness connector of coolant temperature sensor 1.
13. Disconnect the multi-way control valve harness connector.
14. Disconnect the water hose and heater hose.
15. Remove the multi-way control valve mounting bolt, and then
remove the multi-way control valve and gasket.
16. If necessary, remove engine coolant temperature sensor 1 from
the multi-way control valve.
CAUTION:
Handle it carefully and never subject it to impact.
INSTALLATION
Note the following, and install in the reverse order of removal.
Engine Coolant Temperature Sensor 1
CAUTION:
If engine coolant temperature sensor 1 is removed, never reuse it. Replace it with a new one.
Water Hose
Water outlet adapter side
: Vehicle front
JSBIA5711ZZ
: Vehicle front
JSBIA5712ZZ
: Vehicle front
JSBIA5713ZZ
CO-56
< REMOVAL AND INSTALLATION >
[MR EXCEPT FOR NISMO RS MODELS]
MULTI-WAY CONTROL VALVE
• When inserting the water outlet hose (1), align the water outlet
hose paint mark (A) with the mark (B) on the water outlet adapter
(2).
• Check that the distance (A) from the end of the water outlet hose
(1) to the water outlet adapter (2) is within the standard.
• The orientation of the hose clamp tabs must be within
± 15° (b) of
the water outlet hose paint mark (A).
Multi-way control valve side
• When inserting the water outlet hose (1), align the water outlet
hose paint mark (A) with the rib shape (B) on the multi-way control
valve (2).
JSBIA5714ZZ
Dimension (A)
: 5 mm
JSBIA5715ZZ
JSBIA5900ZZ
JSBIA5716ZZ
MULTI-WAY CONTROL VALVE
CO-57
< REMOVAL AND INSTALLATION >
[MR EXCEPT FOR NISMO RS MODELS]
C
D
E
F
G
H
I
J
K
L
M
A
CO
N
P
O
• The orientation of the hose clamp tabs must be within
± 15° (b) of
the water outlet hose paint mark (A).
Inspection
INFOID:0000000012197570
INSPECTION AFTER INSTALLATION
• Start the engine, and check the joints for coolant leakage.
JSBIA5900ZZ
CO-58
< SERVICE DATA AND SPECIFICATIONS (SDS)
[MR EXCEPT FOR NISMO RS MODELS]
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Periodical Maintenance Specification
INFOID:0000000012197571
ENGINE COOLANT CAPACITY (APPROXIMATE)
Unit: (US qt, Imp qt)
Radiator
INFOID:0000000012197572
Unit: kPa (kg/cm
2
, psi)
Engine coolant capacity (With reservoir tank at “MAX” level)
M/T models
8.5 (9, 7-1/2)
CVT models
8.7 (9-2/8, 7-5/8)
Reservoir tank engine coolant capacity (At “MAX” level)
0.6 (5/8, 1/2)
Cap relief pressure
Standard
80 - 100 (0.8 - 1.0, 11.6 - 14.5)
Limit
60 (0.6, 8.7)
Leakage testing pressure
100 (1.0, 14.5)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст